
Диск сцепления 22400M72R00 для Suzuki
Применимый тип:Suzuki
Номер запчасти:22400M72R00, 22400M72R00, 22400M72R00
| Номинальный выход : | |
| Pulley : | 18T |
| Размер : | 19.5+18.5+3 |
| Вес : | Вес: Net weight 0.85, gross weight 0.9 |
| Упаковочные материалы : | Нейтральная упаковка из крафт-бумаги |
| Спотовые / предварительные продажи : | presale |
| Гарантия : | 1 год |
| Номер продукта : |
| Тип : | диск сцепления |
| Спецификация : | 190mm |
| Блок : | 18T |
| Марка : | nuojin |
| Цифры : | 22400M72R00 |
| Качество : | НОВЫЙ |
| Время поставки : | 30 дней |




22400M72R00 Clutch Disc: What It Does
The 22400M72R00 clutch disc is the wear part of the clutch. Lining thickness, spline fit and damper springs all decide how smoothly the vehicle pulls away and how much torque the clutch can hold.
Every unit is checked against the original dimensions before packing. Bolt patterns, diameters and interfaces are matched so the part can be fitted with standard tools.
Specification Summary
- Friction lining matched to the original friction coefficient
- Torsional damper springs in the hub
- Splined hub with the original tooth count
- Balanced assembly ready to fit
Reference Numbers and Cross References
Catalogue references for this part:
- 22400M72R00
Application Notes
On Suzuki installations, check the input shaft splines for wear. A dry or worn spline makes the new disc stick and drag.
Fitment follows the assembly, not the badge. Two vehicles of the same model year can use different parts, so check the number on the old unit.
Failure Modes
Rivets touch the flywheel when the lining is worn out. From that point the flywheel is being machined by steel, and slip becomes rapid.
Damper springs break or seat badly, producing rattle at idle and a knock when the clutch is released. Oil contamination from a leaking seal makes a healthy disc slip.
Fault Symptoms
- Clutch slip in high gears
- Judder or chatter when engaging
- Rattle at idle that stops when the pedal is pressed
- Burning smell after normal driving
- Pedal that needs more travel to release
Checking Before Replacement
Measure lining thickness and look for oil or loose rivets. Check the damper springs for free movement and the splines for fretting.
Inspect the mating surfaces and the fasteners before assembly. Most early failures trace back to something that was not renewed alongside.
Installation Notes
Clean the flywheel and pressure plate faces, check the spigot bearing and the release mechanism, then fit the disc with an alignment tool before torquing the pressure plate in a cross pattern. Lightly grease the splines only, and keep grease off the lining.
Related Parts to Check at the Same Time
- Clutch pressure plate
- Release bearing
- Flywheel
- Gearbox input shaft seal
Quality Control and Supply
Hejian Nuojin Auto Parts Co., Ltd. inspects dimensions, materials and interfaces on every batch, then packs the parts in neutral cartons. Each unit carries a one-year warranty against manufacturing defects.
Frequently Asked Questions
How do I confirm the part number?
Read the number from the old unit, not from a catalogue illustration. Compare the key dimensions at the same time.
Can I fit this without special tools?
Most of these parts fit with standard hand tools. A pulley needs a spline holding tool, and a clutch needs an alignment tool.
What else should be replaced at the same time?
Anything that touches the new part: belts and tensioners for a pulley, brushes for a regulator, the disc, bearing and flywheel face for clutch work.
Why did the original part fail?
Wear, heat and misalignment account for most failures. Correct installation and matching numbers prevent a repeat.
The installation method of Suzuki clutch friction plates varies depending on the model. Here are the general installation steps and precautions: Installation Steps • Preparation: Turn off the engine, park the vehicle on a flat and safe place, pull the handbrake tightly, and prepare tools such as wrenches and screwdrivers, as well as new clutch friction plates. • Removal of related components: For cars, it is necessary to remove the bolts connecting the gearbox and the engine, separate the gearbox from the engine, then remove the fixing bolts of the clutch pressure plate, take off the pressure plate, and then the old clutch plate can be seen and carefully taken out; for motorcycles, find the screws of the clutch housing, unscrew the screws and remove the housing, then take off the clutch lever, and then remove the old clutch plate from the flywheel.Clean the installation area: Use a clean rag to clean the clutch installation area, including the surface of the flywheel and the pressure plate. Remove oil stains, impurities, and dust to prevent the clutch from slipping. Inspect related components: Check whether components such as the clutch driven disc and release bearing are worn or damaged. If there are any problems, they need to be replaced in a timely manner. Install the new friction plate: For a car, correctly install the new clutch plate onto the clutch driven disc, paying attention to the installation direction. Generally, the side of the driven disc with the protruding damping spring should face the pressure plate. For a motorcycle, such as the Suzuki King GS125, during installation, you need to first install the wooden plates, then the metal plates, with one metal plate sandwiched between every two wooden plates, and the last plate should still be a wooden plate.Install the pressure plate: Install the clutch pressure plate back to its original position and tighten the fixing bolts, making sure that the tightening force of the bolts is uniform. • Restore other components: Reinstall the gearbox onto the engine and tighten the connecting bolts; for motorcycles, reinstall the clutch lever onto the clutch housing and secure it with a nut, then reinstall the clutch cover onto the motorcycle and secure it with screws. • Adjustment and testing: For cars, start the engine, test the clutch, check if the stroke and engagement point of the clutch pedal are normal, and make appropriate adjustments if necessary; for motorcycles, reconnect the battery and start the engine for a test run, adjust the clutch lever until a proper pull is felt and smooth shifting is achieved in all gears.
Notes • Keep Clean: Before installation, the friction plates must be kept clean, protected from dust, dirt, and oil. New clutch plates and brake pads should first be soaked in transmission oil to ensure they are fully oiled before assembly. • Pay Attention to Installation Direction: For car clutch friction plates, the side with the boss should face the gearbox, and the side without the boss should face the flywheel; for motorcycles, the wooden plates and metal plates must be installed in a specific order. • Lubricate Related Components: During installation, apply lubricating oil to the splines of the clutch disc to ensure proper lubrication of the driven disc splines and the first shaft splines of the gearbox. However, do not use excessive oil to prevent slipping.Apply force evenly: When tightening bolts, appropriate tools should be used to tighten them diagonally and alternately to avoid deformation of components. • Check the fitting condition: Before installation, check the fitting condition between the splines of the driven plate hub and the input shaft splines to ensure free movement without jamming and no obvious looseness.
References:The content you provided regarding the installation of Suzuki clutch friction plates does not have a clear single source. It is compiled by integrating general knowledge in the field of automobile maintenance and relevant content from multiple professional automotive websites such as Autohome and PCauto. For example, points such as keeping the friction plates clean during installation, avoiding oil contamination, soaking new clutch plates in transmission oil to fully absorb oil before assembly, paying attention to the direction during installation, and ensuring that the side with the boss faces the gearbox are all mentioned in the article "What Are the Precautions for Installing Clutch Friction Plates?" on Autohome and the same-titled article on PCauto. The content about installing the clutch plates of the Suzuki GS125 motorcycle by first installing the wooden plates, then the metal plates, with one metal plate between every two wooden plates comes from the article "Should the Isuzu 700p Clutch Plate Be Placed Right Side Up or Upside Down?" on Autohome.

