
Диск сцепления MZD004 для Ford
Применимый тип:Ford
Номер запчасти:B504-16-460A,B5Y1-16-460,B672-16-460,B504-16-460B,B621-16-460,D504-16-460A,DZ-015,HB08326, K00912,LDF586,J2203002, 319004310,301913000,DZ-029,HB8326,J2203007,H-03019-0017-00,L-03019-0607-01,07G65010J8, K00909,MZD004U,301913000,L-03019-0130-00
| Номинальный выход : | |
| Pulley : | 20T |
| Размер : | Size 21+21+3.5 |
| Вес : | Вес: Net weight 0.75, gross weight 0.8 |
| Упаковочные материалы : | Нейтральная упаковка из крафт-бумаги |
| Спотовые / предварительные продажи : | presale |
| Гарантия : | 1 год |
| Номер продукта : |
| Тип : | диск сцепления |
| Спецификация : | 190mm |
| Блок : | 20T |
| Марка : | nuojin |
| Цифры : | MZD004 |
| Качество : | НОВЫЙ |
| Время поставки : | 30 дней |




Overview of the MZD004 Clutch Disc
The MZD004 clutch disc is the wear part of the clutch. Lining thickness, spline fit and damper springs all decide how smoothly the vehicle pulls away and how much torque the clutch can hold.
Every unit is checked against the original dimensions before packing. Bolt patterns, diameters and interfaces are matched so the part can be fitted with standard tools.
Specification Summary
- Friction lining matched to the original friction coefficient
- Torsional damper springs in the hub
- Splined hub with the original tooth count
- Balanced assembly ready to fit
Reference Numbers and Cross References
Catalogue references for this part:
- MZD004
- B504-16-460
- B504-16-460D
- B628-16-460A
- B504-16-460A
- B5Y1-16-460
- B672-16-460
- B504-16-460B
- B621-16-460
- D504-16-460A
- DZ-015
- HB08326
- K00912
- LDF586
- DZ-029
- HB8326
Application Notes
The disc fits Ford applications. Match the diameter, the spline count and the damper type with the old disc.
Confirm the number against the vehicle before ordering. Where a model was built with more than one driveline or charging variant, the part number is the only reliable guide.
Failure Modes
Lining wear is the normal end. Once the friction material is down to the rivets, the disc slips, the flywheel scores and the smell of burning lining follows the vehicle.
Damper springs break or seat badly, producing rattle at idle and a knock when the clutch is released. Oil contamination from a leaking seal makes a healthy disc slip.
Fault Symptoms
- Clutch slip in high gears
- Judder or chatter when engaging
- Rattle at idle that stops when the pedal is pressed
- Burning smell after normal driving
- Pedal that needs more travel to release
Checking Before Replacement
Check the flywheel and pressure plate faces at the same time. A scored flywheel destroys a new disc quickly.
Inspect the mating surfaces and the fasteners before assembly. Most early failures trace back to something that was not renewed alongside.
Installation Notes
Clean the flywheel and pressure plate faces, check the spigot bearing and the release mechanism, then fit the disc with an alignment tool before torquing the pressure plate in a cross pattern. Lightly grease the splines only, and keep grease off the lining.
Related Parts to Check at the Same Time
- Clutch pressure plate
- Release bearing
- Flywheel
- Gearbox input shaft seal
Quality Control and Supply
Dimension, material and function checks are carried out per batch before packing. Hejian Nuojin Auto Parts Co., Ltd. supplies the part in neutral packaging with a one-year warranty.
Frequently Asked Questions
Is a warranty included?
Yes, one year against manufacturing defects, with neutral packing for resale.
How do I confirm the part number?
Read the number from the old unit, not from a catalogue illustration. Compare the key dimensions at the same time.
Can I fit this without special tools?
Most of these parts fit with standard hand tools. A pulley needs a spline holding tool, and a clutch needs an alignment tool.
What else should be replaced at the same time?
Anything that touches the new part: belts and tensioners for a pulley, brushes for a regulator, the disc, bearing and flywheel face for clutch work.
Installing the clutch friction disc of a Ford vehicle requires following standardized steps to ensure the proper functioning of the clutch system. Below is a general installation process and precautions (specific operations should be carried out in accordance with the vehicle model manual): I. Pre-installation Preparation Component Inspection • Check if the new friction disc has oil stains (if so, clean it with a dedicated cleaning agent to avoid slipping). Ensure the surface of the friction disc is free from wear and cracks, and that the rivets or adhesive layer are secure. • Check if the surfaces of the clutch pressure plate and flywheel are flat, and if there is any ablation or scratches. Repair or replace them if necessary. • Prepare special tools: clutch alignment tool (to ensure the friction disc is concentric with the flywheel), torque wrench, socket, etc.Installation Environment • Ensure the working area is clean to prevent dust and impurities from entering the clutch system. II. Installation Steps Positioning the Friction Disc • Align the clutch friction disc with the center of the flywheel, paying attention to the front and back of the friction disc (there is usually a mark, such as "Facing the Gearbox" or "Flywheel Side", to avoid incorrect installation). • Insert the clutch alignment tool into the center hole of the friction disc and the flywheel pilot bearing (or bushing) to fix the position of the friction disc, ensuring it is concentric with the flywheel.Install the pressure plate • Fit the pressure plate to the flywheel, align the locating pins on the pressure plate with the holes in the flywheel, and evenly install the pressure plate fixing bolts (do not tighten them temporarily). • Gradually tighten the bolts in a diagonal cross sequence (refer to the torque value specified in the vehicle manual, usually 25-40N・m) to avoid deformation of the pressure plate. Remove the alignment tool • After confirming that the pressure plate bolts are fully tightened, pull out the clutch alignment tool.Subsequent Assembly • Install components such as the clutch release bearing and fork, and check whether the release clearance meets the standards. • Install the gearbox, ensuring that the input shaft is smoothly inserted into the center hole of the friction plate without jamming.Notes • Prohibition of oil pollution: If the contact surfaces of the friction plate, pressure plate, and flywheel are contaminated with oil, it will cause the clutch to slip and must be thoroughly cleaned. • Concentricity is crucial: If the friction plate is not concentric with the flywheel, it will make the installation of the transmission input shaft difficult or cause the clutch to shudder. • Operate according to the manual: The specific torque parameters and details may vary for different Ford models (such as Focus, F-150, etc.), so be sure to refer to the maintenance manual of the corresponding model.
References:The content I previously provided regarding "Ford clutch friction plate installation" does not have a specific single source. It is a summary based on the general operating specifications and common procedures for installing Ford automobile clutch friction plates, integrating knowledge from various aspects such as standard steps in automobile repair manuals and practical experience in the automobile repair industry. Different sources of automobile repair materials, such as official repair manuals for Ford models, relevant technical articles on professional automotive websites like Autohome and Pacific Auto Network (as you saw in the previous search results, there are many similar introductions to installation steps), have certain similarities in content. They all revolve around the key points and operational procedures of clutch friction plate installation. I also referred to these common information sources to provide you with accurate and practical installation guidance.

