
Нажимной диск сцепления 30210-VD200 для Nissan
Применимый тип:Nissan
Номер запчасти: 30210-VD200,30210VD200,NSC645
| Номинальный выход : | |
| Pulley : | |
| Размер : | 34.5+34.5+6.5single unit inner box |
| Вес : | Вес: Net weight 8.65 Gross weight 9 |
| Упаковочные материалы : | Нейтральная упаковка из крафт-бумаги |
| Спотовые / предварительные продажи : | presale |
| Гарантия : | 1 год |
| Номер продукта : |
| Тип : | диск сцепления |
| Спецификация : | Outer diameter: 275mm |
| Блок : | |
| Марка : | nuojin |
| Цифры : | 30210-VD200 |
| Качество : | НОВЫЙ |
| Время поставки : | 30 дней |





Overview of the 30210-VD200 Clutch Pressure Plate
A pressure plate is the clamping half of the clutch. On the 30210-VD200 unit the cover, diaphragm spring and release fingers are balanced as one assembly so the clamp load stays even across the friction face.
The part is supplied ready to fit, with the dimensions and the interface points matched to the original. That matters on a service part: a pulley, regulator or clutch component that is close but not correct will fail early and take surrounding parts with it.
Specification Summary
- Diaphragm spring with matched clamp load
- Machined friction face and balanced cover
- Release fingers set to the original height
- Direct replacement for the original flywheel pattern
Reference Numbers and Cross References
The part is listed under the following references:
- 30210-VD200
- 30210VD200
- NSC645
Application Notes
For Nissan installations the gearbox has to come out. Check the flywheel face and the release mechanism while the clutch is open.
Fitment follows the assembly, not the badge. Two vehicles of the same model year can use different parts, so check the number on the old unit.
Failure Modes
Heat is the main enemy. Hot spots and cracks form on the friction face, clamp load drops and the clutch begins to slip under load, usually first in a high gear.
Mechanical wear finishes it: grooved fingers, a worn pivot and a release bearing that howls. Left alone, the bearing wears through the fingers and the clutch will not release at all.
Fault Symptoms
- Clutch slip under acceleration
- Judder when pulling away
- Pedal that bites very high or very low
- Noise when the pedal is pressed
- Burning smell after hill starts
Checking Before Replacement
Check the guide tube and the release mechanism. A worn fork or a dry guide tube makes a new clutch feel wrong and shortens its life.
Replace related wear parts at the same time. A new part fitted against a worn mating surface rarely lasts.
Installation Notes
Clean the flywheel, align the disc with a clutch alignment tool, fit the pressure plate evenly and tighten the bolts in a cross pattern to the specified torque. Fit a new release bearing, check pedal free play and bed the clutch in gently for the first few hundred kilometres.
Related Parts to Check at the Same Time
- Clutch disc
- Release bearing
- Flywheel
- Clutch fork and guide tube
Quality Control and Supply
Dimension, material and function checks are carried out per batch before packing. Hejian Nuojin Auto Parts Co., Ltd. supplies the part in neutral packaging with a one-year warranty.
Frequently Asked Questions
Is a warranty included?
Yes, one year against manufacturing defects, with neutral packing for resale.
How do I confirm the part number?
Read the number from the old unit, not from a catalogue illustration. Compare the key dimensions at the same time.
Can I fit this without special tools?
Most of these parts fit with standard hand tools. A pulley needs a spline holding tool, and a clutch needs an alignment tool.
What else should be replaced at the same time?
Anything that touches the new part: belts and tensioners for a pulley, brushes for a regulator, the disc, bearing and flywheel face for clutch work.
The installation steps and precautions for Nissan clutch pressure plate are as follows: Installation Steps • Preparation Work: Prepare suitable clutch pressure plate, clutch disc, wrenches, screwdrivers, torque wrenches and other tools. Park the vehicle on a flat ground, ensure the engine has cooled down, and disconnect the vehicle power supply. • Removal of Old Components: Lift the vehicle and support it stably, then remove the transmission. Use appropriate tools to loosen the fixing bolts on the pressure plate, take off the old clutch pressure plate and clutch disc, and pay attention to marking the positions and directions of each component. • Cleaning the Installation Position: Carefully clean the flywheel with a cleaning cloth or cleaning agent to remove oil stains, dust and impurities, ensuring that the installation surface is clean and flat.Install the new pressure plate: Accurately install the new pressure plate on the flywheel, ensuring that the locating pins of the pressure plate perfectly align with the locating holes of the flywheel and that the direction is correct. For models such as the Nissan X-Trail, the matching marks on the clutch cover, pressure plate, and diaphragm spring should remain aligned. Then, use a torque wrench to tighten the bolts diagonally and alternately in multiple steps according to the specified value. For example, the tightening torque for the pressure plate fixing bolts of the X-Trail model is 25Nm. • Install the clutch disc: Precisely align the clutch disc with the pressure plate, ensuring that the guide pins and guide holes fit tightly. The side of the clutch driven disc with the damping disc should be installed facing the pressure plate. Gently rotate the clutch disc to check if it can move freely without any jamming.Installing release bearing and other components: Apply base grease to each fulcrum, supporting surface, and release bearing, then install the release bearing and other components in sequence to ensure correct installation. For the X-Trail model, both ends of the release fork shaft must be concentric, and the installation position of the clutch release fork shaft transmission arm must be 195mm-205mm away from the fixed cable nut bracket. • Reassembling the transmission: Install the transmission back to its original position and recheck the tightness of the connecting bolts with a torque wrench. • Inspection and debugging: After installation, start the engine, check if the clutch operates smoothly, conduct shift tests, and inspect for abnormal noises, slipping, and other issues. Meanwhile, adjust the free travel of the clutch pedal to an appropriate range, such as 15mm-25mm for the X-Trail model.
Notes • Avoid contact with oil stains: It is strictly forbidden to touch the pressure plate with oil-stained hands, rags, or other oil-contaminated objects to prevent oil stains from affecting its working performance. • Check component fit: Carefully inspect the fit between the splines of the driven plate hub and the input shaft splines to ensure there is no jamming or looseness between them. • Pay attention to bolt tightening methods: All bolts should be tightened multiple times in a diagonal alternating manner according to the specified torque to ensure a firm connection between the pressure plate and the flywheel, preventing loosening and wear.
References:The content you provided regarding the installation of Nissan clutch pressure plates does not have a clear single specific source. It is compiled by integrating professional automotive repair knowledge, automotive brand repair manuals, and content from multiple automotive-related websites. Some of the content is consistent with the steps and precautions for Nissan X-Trail clutch installation on the Autohome website. For example, the requirements to ensure that the pressure plate positioning pins align with the flywheel positioning holes and the installation direction of the clutch disc are mentioned in several articles on Autohome. At the same time, the general steps and key points for clutch pressure plate installation on PCauto, such as cleaning the installation area and cross-tightening bolts according to the specified torque, are also consistent with the content you provided. In addition, the content on the carpedia.club website regarding the installation of the Nissan Qashqai clutch, which mentions marking the pressure plate position and uniformly tightening the bolts, is also consistent with some of the key points you mentioned.

