
Нажимной диск сцепления 6WK2101 для Volvo
Применимый тип:Volvo
Номер запчасти:3400037031,037031,8112308,8112848 6WK2101 AP0127 3400037031 K2101 638290600 10030423 HD20 HK38077 10552020
| Номинальный выход : | |
| Pulley : | |
| Размер : | 380mm |
| Вес : | Вес: pan--Net weight 22.65 Gross weight 23.45 pian--Net weight 6, gross weight 6.5 |
| Упаковочные материалы : | Нейтральная упаковка из крафт-бумаги |
| Спотовые / предварительные продажи : | В наличии |
| Гарантия : | 1 год |
| Номер продукта : |
| Тип : | нажимной диск |
| Спецификация : | |
| Блок : | |
| Марка : | NUOJIN |
| Цифры : | 3400037031 |
| Качество : | НОВЫЙ |
| Время поставки : | 30 дней |








About the 6WK2101 Clutch Pressure Plate
The 6WK2101 clutch pressure plate clamps the friction disc against the flywheel. Spring force comes from a diaphragm or coil springs, and release bearing travel lifts the fingers to disengage the drive.
Every unit is checked against the original dimensions before packing. The interfaces are what decide service life, and they are measured on every batch.
Specification Summary
- Diaphragm spring with matched clamp load
- Machined friction face and balanced cover
- Release fingers set to the original height
- Direct replacement for the original flywheel pattern
Reference Numbers and Cross References
Catalogue references for this part:
- 3400037031
- 037031
- 8112308
- 8112848
- 6WK2101
- AP0127
- K2101
- 638290600
- 10030423
- HD20
- HK38077
Application Notes
For Volvo installations the gearbox has to come out. Check the flywheel face and the release mechanism while the clutch is open.
Fitment follows the assembly, not the badge. Two vehicles of the same model year can use different parts, so check the number on the old unit.
Failure Modes
Overheating removes clamp load. The diaphragm loses tension, the pedal feels light and the engine revs without the vehicle accelerating.
Worn release fingers and a tired release bearing follow. A bearing that has been running dry wears the finger tips, and the pedal gets heavy or noisy.
Fault Symptoms
- Clutch slip under acceleration
- Judder when pulling away
- Pedal that bites very high or very low
- Noise when the pedal is pressed
- Burning smell after hill starts
Checking Before Replacement
Check the guide tube and the release mechanism. A worn fork or a dry guide tube makes a new clutch feel wrong and shortens its life.
Replace related wear parts at the same time. A new part fitted against a worn mating surface rarely lasts.
Installation Notes
Clean the flywheel, align the disc with a clutch alignment tool, fit the pressure plate evenly and tighten the bolts in a cross pattern to the specified torque. Fit a new release bearing, check pedal free play and bed the clutch in gently for the first few hundred kilometres.
Related Parts to Check at the Same Time
- Clutch disc
- Release bearing
- Flywheel
- Clutch fork and guide tube
Quality Control and Supply
Hejian Nuojin Auto Parts Co., Ltd. inspects dimensions, materials and interfaces on every batch, then packs the parts in neutral cartons. Each unit carries a one-year warranty against manufacturing defects.
Frequently Asked Questions
Is a warranty included?
Yes, one year against manufacturing defects, with neutral packing for resale.
How do I confirm the part number?
Read the number from the old unit, not from a catalogue illustration. Compare the key dimensions at the same time.
Can I fit this without special tools?
Most of these parts fit with standard hand tools. A pulley needs a spline holding tool, and a clutch needs an alignment tool.
What else should be replaced at the same time?
Anything that touches the new part: belts and tensioners for a pulley, brushes for a regulator, the disc, bearing and flywheel face for clutch work.
Installation Method for Volvo Clutch Kit
Preparation Work
Park the vehicle on a flat and safe area, pull the parking brake, lift the vehicle with a jack, and securely support it with safety stands to ensure the vehicle does not move during installation.
Prepare tools such as socket wrenches, combination wrenches, a jack, and a torque wrench, as well as a new Volvo clutch kit.
Drain the gear oil from the transmission, remove the connecting components between the transmission and the engine (including bolts and drive shafts), and mark them for accurate reinstallation later.
Remove the Old Clutch Kit
Mark the assembly positions on the clutch cover assembly and flywheel assembly to ensure accurate reset during the installation of the new kit.
Use a socket wrench to remove the bolts on the clutch pressure plate, loosening them gradually in a diagonal sequence to avoid pressure plate deformation due to uneven force. Then remove the clutch pressure plate and clutch disc.
Remove the release bearing. Usually, the release bearing is connected to the release fork; first remove the release fork from the transmission, then take out the release bearing.
Install the New Clutch Kit
Clean the surfaces of the flywheel and pressure plate to remove oil, rust, and impurities, ensuring a clean and flat installation surface.
Apply lubricating oil to the pilot bearing on the flywheel to ensure smooth operation of the pilot bearing.
Place the new clutch disc on the flywheel, paying attention to its direction. Generally, the convex side should face the transmission, and it must be accurately aligned with the splines and drive shaft.
Install the pressure plate, place it stably on the flywheel, align it with the previously marked positions, and tighten the bolts according to the specified torque and sequence to ensure the pressure plate is firmly installed with uniform force. The torque for pressure plate bolts may vary by model (refer to the vehicle maintenance manual for details), generally around 25Nm.
Install the release bearing and release fork assembly to keep the flywheel and driven disc concentric. Mount the release bearing on the transmission input shaft, ensure it is correctly positioned and can move smoothly, and apply lithium-based grease to the connection points such as the release fork and release bearing.
Reset Other Components and Debug
Reinstall the transmission onto the engine, tighten the connecting bolts, and reconnect all previously disconnected wires and pipelines.
Add an appropriate amount of gear oil to the transmission.
Adjust the clutch pedal free travel, which should generally be adjusted to 15mm-25mm (refer to the vehicle maintenance manual for specific values).
Start the engine and conduct a test run to check the clutch operation, including whether the clutch disengages and engages smoothly, and if there are any abnormal noises or vibrations during vehicle operation.
Pre - installation Preparations
Parts Inspection: Ensure that the clutch kit matches the Volvo model. Check each component for damage, wear, or deformation. For example, check whether the pressure plate surface is flat and whether the friction material of the clutch disc is excessively worn.
Component Cleaning: Gently wipe the surfaces of the clutch pressure plate, clutch disc, and flywheel with a damp cloth to remove oil stains, rust, and impurities. Do not use a grinding wheel, dry brush, or compressed air for cleaning to avoid damaging the components.
Installation Process
Component Installation Direction: The clutch disc has a specific installation direction. The side of the driven disc with the shock absorber disc should face the pressure plate direction, and it should be precisely aligned with the splines and the drive shaft. When installing the clutch cover, ensure that it is aligned with the alignment marks of the pressure plate and the diaphragm spring.
Bolt Tightening: When tightening the pressure plate bolts, gradually tighten them in a diagonal order to ensure that the pressure plate is evenly stressed. The torque of the pressure plate bolts may vary for different models. Generally, it is about 25 N·m. Refer to the vehicle maintenance manual for specific values.
Bearing Installation and Lubrication: When installing the release bearing, ensure that it fits well with the release fork. Apply lithium - based lubricating grease to each pivot point, the bearing surface, and the release bearing to reduce friction.
Coaxiality Assurance: Use the first shaft of the transmission as a guide rod during installation to ensure that the coaxiality deviation between the clutch and the flywheel is within the allowable range, which provides convenience for the subsequent installation of the transmission.
Post - installation Debugging
Adjustment of Clutch Pedal Free Play: The free play of the clutch pedal should generally be adjusted to 15 - 25 mm. Refer to the vehicle maintenance manual for specific values to ensure the normal separation and engagement of the clutch.
Operation Check: Start the engine and check the working condition of the clutch, including whether the separation and engagement are smooth, and whether there are any abnormal noises or vibrations during the vehicle's operation.

