
Выжимной подшипник BT-128 для Toyota
Применимый тип:Toyota
Номер запчасти:31230-60241 31230-60230 31230-60240 BT-128 68SCRN54PQ-2-F 315 1654 215 J2402042 315 1654 240 3121060230 3125035451 3121060290 201-17047
| Номинальный выход : | |
| Pulley : | |
| Размер : | |
| Вес : | |
| Упаковочные материалы : | Нейтральная упаковка из крафт-бумаги |
| Спотовые / предварительные продажи : | В наличии |
| Гарантия : | 1 год |
| Номер продукта : |
| Тип : | выжимной подшипник |
| Спецификация : | |
| Блок : | |
| Марка : | NUOJIN |
| Цифры : | 31230-60241 |
| Качество : | НОВЫЙ |
| Время поставки : | 30 дней |




Overview of the BT-128 Clutch Release Bearing
The BT-128 clutch release bearing is the bearing that presses on the pressure plate fingers when the pedal goes down. It turns only while the clutch is disengaged, which is why a worn bearing is noisy with the pedal pressed and quiet when released.
The part is supplied ready to fit, with the dimensions and the interface points matched to the original. That matters on a service part: a pulley, regulator or clutch component that is close but not correct will fail early and take surrounding parts with it.
Specification Summary
- Sealed, pre-greased bearing
- Hardened raceways for thrust load
- Guide sleeve interface matched to the original
- Direct replacement for the original carrier
Reference Numbers and Cross References
Match the unit by any of these numbers:
- 31230-60241
- 31230-60230
- 31230-60240
- BT-128
- 68SCRN54PQ-2-F
- 3121060230
- 3125035451
- 3121060290
- 201-17047
Application Notes
On Toyota installations the gearbox has to come out. Renew the bearing whenever the clutch is opened, regardless of how it feels.
Confirm the number against the vehicle before ordering. Where a model was built with more than one driveline or charging variant, the part number is the only reliable guide.
Failure Modes
Dry raceways make noise first and seize later. Once the bearing seizes it spins on the guide sleeve and wears the sleeve or the fingers.
Worn fingers and a dry guide sleeve accelerate it. A bearing running against a dry sleeve sticks, and the resulting side load shortens its life.
Fault Symptoms
- Whine or rumble with the pedal pressed
- Noise that stops when the pedal is released
- Grating feel through the pedal
- Hard or sticky pedal release
- Clutch that drags when cold
Checking Before Replacement
Inspect the pressure plate fingers for grooves. A grooved plate will destroy a new bearing quickly.
Replace related wear parts at the same time. A new part fitted against a worn mating surface rarely lasts.
Installation Notes
Clean the guide sleeve, apply a thin film of high-temperature grease, and slide the bearing on squarely. Fit the fork and check that the bearing sits flat on the fingers before refitting the gearbox. Bleed the release system where hydraulic.
Related Parts to Check at the Same Time
- Clutch pressure plate
- Clutch disc
- Guide sleeve and fork
- Release cylinder
Quality Control and Supply
Hejian Nuojin Auto Parts Co., Ltd. inspects dimensions, materials and interfaces on every batch, then packs the parts in neutral cartons. Each unit carries a one-year warranty against manufacturing defects.
Frequently Asked Questions
How do I confirm the part number?
Read the number from the old unit, not from a catalogue illustration. Compare the key dimensions at the same time.
Can I fit this without special tools?
Most of these parts fit with standard hand tools. A pulley needs a spline holding tool, and a clutch needs an alignment tool.
What else should be replaced at the same time?
Anything that touches the new part: belts and tensioners for a pulley, brushes for a regulator, the disc, bearing and flywheel face for clutch work.
Why did the original part fail?
Wear, heat and misalignment account for most failures. Correct installation and matching numbers prevent a repeat.
- Pre-installation Preparation: Lift the vehicle to an appropriate height. Prepare professional disassembly tools, a new clutch release bearing, a torque wrench, and other necessary tools. Ensure the release bearing is clean, free of rust-preventive grease and debris.
- Install the Release Fork Bushing: Use a special tool to press the release fork bushing into the transmission case.
- Install the Release Fork Shaft: Attach the return spring to the left end of the release fork shaft, then insert the left end into the left hole of the transmission case first, followed by inserting the right end into the right bushing hole. Subsequently, install the left release fork shaft bushing and bushing seat. Apply sealant to the gasket and guide sleeve, mount them on the front of the transmission case, and tighten the bolts to a torque of 15N·m. Tighten the bolt at the rear of the transmission case to 15N·m to lock the release fork shaft. Verify that the release fork shaft rotates flexibly without left-right movement.
- Press-fit the Release Bearing: Use a special tool to vertically press the release bearing into the release bearing housing.
- Install the Clutch Driven Disc and Pressure Plate Assembly: Place the driven disc on the engine flywheel with the protruding side of the damping springs facing outward, and position it using a centering rod. Mount the pressure plate assembly, then tighten the bolts at intervals with a torque wrench to a torque of 25N·m (follow a diagonal sequence for even force distribution).
- Lubricate Relevant Components: Apply an appropriate amount of high-temperature grease to the ball pins of the clutch release levers, the tips of the release levers, and the contact area between the release bearing and the release fork.
- Assemble the Release Bearing and Release Fork: Install the lubricated release bearing onto the release fork, ensuring it fits securely into the fork's grooves or is fastened with retaining clips.
- Subsequent Reinstallation: Reattach the transmission and other components in the reverse order of disassembly.
- Adjust the Clutch: Adjust the clutch pedal free travel to the standard range of 5-15mm. To adjust, loosen the lock nut, rotate the push rod until the desired free travel is achieved, then retighten the lock nut.
1. Component Inspection
Check Bearing Quality: Ensure the clutch release bearing is free of damage, deformation, and rotates flexibly. Defects in the bearing may cause abnormal clutch operation, such as abnormal noise, jamming, or other issues.
Inspect Other Relevant Components: Simultaneously check for wear, damage, or other faults in related components like the clutch pressure plate and clutch disc. Replace faulty parts promptly to avoid affecting the overall performance of the clutch system.
2. Installation Process
Maintain Cleanliness: Keep the work area clean and tidy to prevent debris from entering the clutch system. Clean the installation site to remove oil stains and impurities before installation, as these foreign objects can impair the normal operation and service life of the release bearing.
Use Proper Tools: Utilize special tools during installation (e.g., a dedicated tool for pressing the release bearing into place). Avoid direct impact with hard objects like hammers to prevent bearing damage.
Ensure Correct Installation Direction: The release bearing has a specific installation orientation and must be installed in accordance with the vehicle’s repair manual. For example, when fitting the release bearing onto the release sleeve in certain models, ensure proper alignment of its grooves or retaining clips.
Lubricate Relevant Parts: Apply an appropriate amount of high-temperature grease to the surface of the release bearing, the ball pins of the release levers, the tips of the release levers, and the contact area between the release bearing and the release fork to reduce friction and wear.
Follow Installation Sequence: When installing the clutch pressure plate assembly, use a centering tool or the transmission input shaft for centering to ensure coaxiality between the driven disc and the pressure plate (facilitating input shaft installation). Fasten the pressure plate bolts only after the pressure plate is fully in contact with the flywheel, tightening them sequentially in a diagonal pattern to ensure secure mounting and uniform force distribution.
3. Post-Installation Inspection
Verify Installation Position: After installation, check that the release bearing is correctly positioned and that the release fork moves flexibly without jamming or loosening.
Adjust Clutch Pedal Travel: Adjust the clutch pedal free travel to match the vehicle’s technical specifications. For instance, the standard free travel for the clutch pedal in some Toyota models is 5-15mm, ensuring normal clutch engagement and disengagement.
Test Drive Inspection: Start the vehicle and perform several gear shifts to check the clutch operation. Confirm there are no abnormal noises or jolts; troubleshoot and resolve any issues promptly if detected.
References:

