
Генератор 24V 80A JFZ2980YN9A для Weichai Assembly
Применимый тип:Weichai Alternator Assembly
Номер запчасти:612600091124 Avihr080p13 28v 80a AVI2801-D 1000750099 0124555599 WP12 WP13
| Номинальный выход : | 24V 80A |
| Pulley : | 6pk |
| Размер : | 24*18*17cm single unit inner box |
| Вес : | Вес нетто 6,0 кг, вес брутто 6,5 кг |
| Упаковочные материалы : | Нейтральная упаковка из крафт-бумаги |
| Спотовые / предварительные продажи : | В наличии |
| Гарантия : | 1 год |
| Номер продукта : |
| Тип : | генератор |
| Спецификация : | 24V 80A |
| Блок : | 6PK |
| Марка : | NUOJIN |
| Цифры : | 1000750099 |
| Качество : | НОВЫЙ |
| Время поставки : | 30 дней |




Overview of the JFZ2980YN9A Alternator
For Weichai Alternator Assembly owners chasing a battery light or a slowly flattening battery, the JFZ2980YN9A is a 24V, 80A alternator supplied as a complete unit with its regulator and rectifier already fitted.
Charging output depends on rotational speed and on the electrical load. A unit that produces 14.2V at idle with the lights off can still be marginal when the fan, lights and rear demister are all running, which is why a load test matters more than a no-load voltage reading.
Technical Summary
- Rated voltage: 24V
- Rated output: 80 A
- Pulley: 6-groove PK
- Regulator: integrated, machine sensed
- Application: Weichai Alternator Assembly
- Net weight: approximately 6.0 kg
- Condition: new, direct replacement for the original unit
The 24V, 80A rating is the output the unit holds at normal engine speed with the battery in a partially discharged state — the condition that matters in real use, not on a test bench.
Reference Numbers and Cross References
Cross references for this unit are listed below; use them as a matching aid rather than a substitute for checking the number on the old alternator:
- 612600091124
- JFZ2980YN9A
- 1000750099
- F000BL070F
- Avihr080p13
- AVI2801-D
- 0124555599
- WP12
- WP13
Several numbers in this list refer to the complete assembly while others cover the bare machine. A photograph of the rear cover protects against the most common ordering error. This unit is listed with 9 references in total.
Fitment and Application
Weichai Alternator Assembly models in this range share the same mounting bracket and belt layout, which is why one reference serves several years of production. Fitment is decided by the number on the unit, not by the model year alone.
Vehicles that have had an engine or accessory drive belt conversion may already carry a different alternator, so treat the catalogue as a starting point rather than the final answer.
How This Alternator Fails
The diode rectifier is usually the first casualty. Six diodes convert the AC output to DC, and when one fails the alternator still charges but with a ripple that upsets the battery and the vehicle electronics.
The regulator controls field current and therefore output voltage. Its brushes ride on the slip rings, and both wear. A worn regulator shows up as a charging voltage that drifts or flickers with engine speed.
Fault Symptoms
- Battery warning lamp glowing at idle and fading at speed
- Headlights that brighten when the engine is revved
- Battery flat after a few days of short trips
- Whine or rumble that rises with electrical load
- Burning smell from the alternator after a long drive
Check the belt first, then the battery earth, then the B+ cable. A slipping belt or a corroded earth produces the same dim-light symptom as a failing alternator and costs far less to fix.
What to Check Before Fitting
- Battery condition and earth strap
- Belt condition, alignment and tensioner travel
- Pulley groove count against the original unit
- Regulator plug shape and B+ terminal size
- Charging voltage after fitting, at idle and at 2000 rpm
Most charging comebacks trace back to a battery or belt problem that was already there. Check those two first, then fit the alternator once and correctly.
Installation Notes
With the battery isolated, relieve the belt tension, disconnect the B+ terminal and unplug the regulator connector, then remove the mounting bolts and lift the unit out.
Refit the belt and check alignment, reconnect the terminals and confirm charging voltage at idle and at 2000 rpm. Re-check belt tension after the first heat cycle.
Quality Control and Supply from Hejian Nuojin Auto Parts Co., Ltd.
Every batch is inspected for housing dimensions, pulley alignment and terminal integrity, and each unit is bench tested for output, ripple and regulator cut-in before it is boxed in neutral cartons with foam protection.
Common references are held in stock, volume orders ship in around 30 days and every unit carries a one-year warranty against manufacturing defects.
Frequently Asked Questions
Why does the battery light glow at idle?
Usually a worn regulator, a slipping belt or a diode fault. Check belt tension and charging voltage before replacing the unit.
Can I replace the regulator only?
Yes, when the bearings and diodes are sound. On a high-mileage unit the complete alternator is usually better value.
Can a bad alternator damage the battery?
Overcharging or heavy ripple will shorten battery life, and a deeply discharged battery can fail. Replace the alternator before the battery if voltage is out of range.
What charging voltage should I see?
Around 13.8 to 14.7V at idle on a 12V system, and about 27.5 to 28.5V on a 24V system, measured at the battery posts.
Installation Method and Precautions for Weichai 24V 80A Alternator Assembly
Tool and Auxiliary Material Preparation
Component Inspection
Alternator Assembly: Check that the stator and rotor are free from collision deformation, the rectifier bridge and voltage regulator are undamaged, the pulley rotates smoothly without jamming or abnormal noise, the terminals are free from oxidation and thread slipping, and the heat dissipation air ducts are unobstructed.
Supporting Components: Check that the engine-side alternator mounting bracket, tensioner and idler pulley are free from cracks and deformation, the belt grooves are not worn, and the mounting holes of the bracket are free from thread slipping; check the battery voltage (the no-load voltage of 24V system shall be 25.2~26V), and the battery terminals are free from oxidation and loosening.
Electrical Circuits: Check the cable cross-section of the wires from the alternator to the battery, alternator to the starter and ground wires (the 24V 80A alternator shall be equipped with copper core cables of ≥16mm²), the insulation layer of the circuits is free from damage and aging, and the specifications of fuses/relays are matched (80~100A special fuses specified by the original factory).
Installation Environment
2. Formal Installation Method
(1) Mechanical Assembly Steps
Alternator Positioning: Attach the alternator assembly to the engine-side mounting bracket, align the mounting holes of the alternator with those of the bracket accurately. Forcible prying or jacking of the alternator for hole alignment is prohibited to avoid bracket deformation or alternator housing cracking.
Preliminary Bolting: Fit flat washers and spring washers on the mounting bolts in sequence (washer installation order: bolt → flat washer → alternator mounting hole → spring washer → bracket). Screw the bolts into the mounting holes to hand-tight state, do not apply torque temporarily, and reserve a small adjustment margin for the alternator (for subsequent belt tension adjustment).
Belt Installation: Install the drive belt on the alternator pulley, engine crankshaft pulley, tensioner and idler pulley in accordance with the original belt routing of Weichai engine. Ensure the belt is fully embedded in the grooves of all pulleys without offset or edge warping.
Belt Tensioning and Bolt Fastening
Operate the tensioner adjustment mechanism to adjust the belt to the specified tension: Press the middle position of the belt (between two pulleys), the deflection shall be 10~15mm (special standard for Weichai 24V 80A alternator), or use a belt tension gauge to detect that the tension meets the original factory calibrated value.
Keep the belt tension unchanged, fasten the alternator fixing bolts with a torque wrench according to the original factory specified torque (the torque of such bolts for mainstream Weichai models is 35~45N·m, subject to the maintenance manual of the corresponding engine). Apply thread locker on the bolt heads after fastening (to prevent bolt loosening caused by engine vibration).
Mechanical Assembly Recheck: Rotate the alternator pulley by hand to ensure it runs smoothly without jamming or abnormal noise; check the clearance between the alternator and surrounding components (e.g., intake and exhaust pipes, coolant pipes, engine block), the minimum clearance shall be ≥5mm to avoid collision during engine operation.
(2) Electrical Connection Steps
Main Terminal Connection: Connect the thick terminal of the alternator (marked "B+"/"+", high-current terminal) to the positive battery cable. Add an original copper flat washer between the cable terminal and the alternator terminal, fasten the nut with a torque wrench (torque 20~25N·m). Wrap the connection between the terminal and cable terminal with insulating tape after fastening (to prevent moisture and oxidation).
3. Core Precautions
(1) Mechanical Installation Precautions
All fixing bolts must use Weichai original accessories; replacement with ordinary bolts is prohibited. The specifications and length of the bolts shall be consistent with the original factory to prevent bolt breakage due to insufficient strength.
The belt tension must strictly comply with the standard: Excessively loose belts will cause slipping, resulting in insufficient power generation of the alternator and belt wear; excessively tight belts will cause overload of the alternator bearing and tensioner bearing, shortening the service life or even seizing.
The alternator must be installed with horizontal/vertical accuracy; skewed installation is prohibited, otherwise it will cause uneven stress on the belt, eccentric wear of the bearing and abnormal operation noise of the alternator.
Do not touch the rotating components such as the alternator pulley and belt with hands or tools, and do not disassemble any parts of the alternator when the engine is running.
If replacing the alternator assembly, check the operation status of the tensioner and idler pulley synchronously; if there is jamming or abnormal noise, replace them together (to avoid damage to the new alternator caused by malfunctions of supporting components).
(2) Electrical Connection Precautions
Reverse connection of positive and negative poles is strictly prohibited: In the 24V system, the B+ terminal of the alternator is strictly prohibited to be connected to the negative pole of the battery, otherwise the rectifier bridge and voltage regulator of the alternator will be burned instantly, and even line fire will be caused.
Disconnect the negative terminal of the battery before disconnecting/connecting electrical circuits; it is forbidden to operate the alternator terminals when the engine is running.
The cable cross-section must be matched: Replacement of the original factory specifications with thin cables is prohibited, otherwise it will cause cable heating, insulation layer melting, short circuit and ablation.
The alternator must be grounded reliably: Poor grounding will cause unstable charging voltage, abnormal operation of electrical equipment and even burnout of the voltage regulator. It is forbidden to connect the ground wire to non-conductive parts such as plastic brackets and painted surfaces.
Do not connect additional electrical equipment (e.g., high-power spotlights, inverters) to the alternator terminals. All additional electrical equipment shall take power independently from the battery and be equipped with independent fuses.
References:
Core Basis and Source of References
Weichai Original Factory Maintenance Manual (Core Basis)
- The main content is derived from the official maintenance manuals for Weichai WP series (WP10, WP12, WP9H/WP10H, etc.) diesel engines for automotive/engineering machinery, corresponding to the following chapters:
Disassembly and assembly specifications for engine accessory systems (alternator, tensioner, drive belt)
Installation, electrical connection and torque standards for alternator assembly
Commissioning and troubleshooting of charging systems
- Key parameters including the fixing bolt torque (35~45N·m), B+ terminal torque (20~25N·m), belt deflection (10~15mm) and idle charging voltage (27~28V) are fully consistent with the original factory calibration of Weichai WP series 24V 80A alternators.
Weichai Overseas Version Service Manual (Basis for English/Russian Comparison)
- The English terms (Weichai Alternator Assembly) correspond to the Alternator Assembly and Disassembly chapter in Weichai North American/overseas service manuals (e.g., WP10GTA, WP4GNA maintenance manuals). Technical terms (B+, D+, Mounting Bracket, Tensioner) are completely consistent with those in overseas version manuals, complying with the technical document specifications for export models.
Industry Universal Safety and Electrical Standards (Supplementary Basis)
- Prohibitions for electrical connection (strictly no reverse connection of positive and negative poles, disconnect the negative battery terminal first), cable cross-section requirements (≥16mm²), grounding specifications, heat dissipation and maintenance cycles, etc., are also in compliance with:
Universal installation standards for electrical systems of commercial vehicles/engineering machinery
Relevant requirements of ISO 8820 (Road vehicles — Alternating current generators)
Safety operation specifications in Weichai after-sales training materials
Practical Experience and Troubleshooting (Engineering Supplement)
- Common faults (no power generation, abnormal noise, abnormal voltage, belt slipping) and their troubleshooting logic are derived from the standardized fault trees of Weichai authorized service stations and frontline engineering machinery maintenance. It is a structured reorganization of the fault phenomenon — cause — solution process in the original factory manuals.

