
Генератор 12V F00E100026 для Ford Volvo
Применимый тип:Ford Volvo
Номер запчасти:0121615014,01216151140125711040,30773111,31288879,36000207.36001497,0125711040.0125711048.0986080810,1541451,2099471,0986082560,F00E100026,DA2144, DRA0052, DRA1034
| Номинальный выход : | 12v 150a |
| Pulley : | 5PK |
| Размер : | 24*18*17single unit inner box |
| Вес : | Вес нетто 5 кг |
| Упаковочные материалы : | Нейтральная упаковка из крафт-бумаги |
| Спотовые / предварительные продажи : | В наличии |
| Гарантия : | 1 год |
| Номер продукта : | hLQS145000025225 |
| Тип : | генератор |
| Спецификация : | 12v 150a |
| Блок : | 5PK |
| Марка : | 诺进 |
| Цифры : | 0121615014 |
| Качество : | НОВЫЙ |
| Время поставки : | 30 дней |


Overview of the F00E100026 Alternator
The F00E100026 is a 12V alternator for Ford Volvo. It is a claw-pole machine with an integrated regulator, balanced at the factory so it runs quietly at idle and at speed.
Charging output depends on rotational speed and on the electrical load. A unit that produces 14.2V at idle with the lights off can still be marginal when the fan, lights and rear demister are all running, which is why a load test matters more than a no-load voltage reading.
Specifications at a Glance
- Rated voltage: 12V
- Pulley: 5-groove PK
- Regulator: integrated, machine sensed
- Application: Ford Volvo
- Net weight: approximately 5 kg
- Condition: new, direct replacement for the original unit
The electrical rating matches the original unit, so the existing wiring and battery sensing circuit can be reused without modification.
Reference Numbers and Cross References
Cross references for this unit are listed below; use them as a matching aid rather than a substitute for checking the number on the old alternator:
- 0121615014
- 01216151140125711040
- 30773111
- 31288879
- 36000207.36001497
- 1541451
- 0986082560
- F00E100026
- DA2144
- DRA0052
- DRA1034
Where the label on the old unit has faded, compare the pulley groove count, the mounting ears and the plug shape with the photographs before ordering. This unit is listed with 11 references in total.
Matching the Unit to the Vehicle
This alternator family was fitted across a range of Ford applications as engines and electrical loads were revised. The unit here covers the references above and is a direct replacement where those numbers match.
If the number on the old alternator falls outside the list above, send the engine code and a photograph of the rear cover before ordering. A unit with the right housing but a different regulator plug will not connect cleanly.
What Wears Out First
Bearings carry the rotor at engine speed for the life of the vehicle. Once the front bearing dries out, the unit starts to whine, and the noise gets worse with electrical load rather than with engine speed alone.
The regulator controls field current and therefore output voltage. Its brushes ride on the slip rings, and both wear. A worn regulator shows up as a charging voltage that drifts or flickers with engine speed.
What to Look For
- Battery light on with the engine running
- Dim or pulsing interior lights
- Voltage at the battery below 13.5V with the engine idling
- Belt squeal that appears when a heavy load switches on
- Overheating alternator body after a short run
A load test separates a tired alternator from a tired battery. Switch on the lights, blower and rear demister and watch the voltage: a healthy unit holds its output, a worn one sags.
Pre-Fit Checklist
- Battery state of charge and age
- Condition of the B+ cable and its fuse
- Pulley type: solid, clutch or overrunning
- Mounting ear dimensions against the bracket
- Belt routing after the new unit is fitted
A new alternator on a tired battery or a glazed belt will not restore charging. Test the simple items before the unit goes on.
Fitting the Replacement
With the battery isolated, relieve the belt tension, disconnect the B+ terminal and unplug the regulator connector, then remove the mounting bolts and lift the unit out.
Fit the replacement, reconnect the plug and B+ cable, then refit the belt and set tension to specification. Start the engine and confirm charging voltage at idle before the first drive.
Quality Control and Supply from Hejian Nuojin Auto Parts Co., Ltd.
Every batch is inspected for housing dimensions, pulley alignment and terminal integrity, and each unit is bench tested for output, ripple and regulator cut-in before it is boxed in neutral cartons with foam protection.
Standard references are kept as spot goods, volume orders are delivered in around 30 days and each alternator carries a one-year warranty against manufacturing defects.
Frequently Asked Questions
Why does the battery light glow at idle?
Usually a worn regulator, a slipping belt or a diode fault. Check belt tension and charging voltage before replacing the unit.
Does the alternator come with a pulley?
Yes, the unit is supplied with its pulley fitted as shown in the photographs, so the original belt can be reused.
What charging voltage should I see?
Around 13.8 to 14.7V at idle on a 12V system, and about 27.5 to 28.5V on a 24V system, measured at the battery posts.
Can a bad alternator damage the battery?
Overcharging or heavy ripple will shorten battery life, and a deeply discharged battery can fail. Replace the alternator before the battery if voltage is out of range.
General Installation Method for Ford/Volvo 12V Alternators
I. Pre-installation Preparation
Safety Protection
Disconnect the negative battery cable to prevent short circuits and electrical component burnout during installation.
Wear insulated gloves and safety goggles to avoid skin contact or eye exposure to engine oil and coolant.
Tools and Accessories
Essential Tools: Socket wrench set (10–19mm), torque wrench, ratchet wrench, screwdrivers, trim panel removal tool.
OEM Parts: Alternator unit, alternator mounting bolts, adjustment bolts, drive belt, belt tensioner (if replacement is required).
Auxiliary Materials: Medium-strength thread locker (e.g., Loctite 243), anti-seize compound, cleaning cloths, engine bay cleaner.
Parts Inspection
Verify that the alternator model, voltage rating (12V), and connector type match the OEM specifications.
Check that the alternator bearing rotates smoothly (no jamming or abnormal noise), and ensure the rectifier and stator windings are free of damage or burn marks.
Inspect the drive belt for cracks, aging, or delamination; confirm the belt tensioner has proper elasticity.
II. Core Installation Steps
Step 1: Locate the Alternator Mounting Position
The alternator is typically mounted on the front of the engine, attached to the engine block via a main mounting bracket and an adjustment bracket. For some Volvo models, it may be necessary to remove the intake manifold or engine cover to access the mounting position.
Thoroughly clean oil, dirt, and rust from the mounting bracket surface, then apply a thin layer of anti-seize compound to prevent bolt seizure.
Step 2: Secure the Alternator Unit
Place the alternator into the mounting bracket, align the main mounting holes, and insert the main mounting bolts (the typical torque value for main bolts is 45–55 N·m for Ford models and 50–60 N·m for Volvo models; always refer to the vehicle-specific OEM service manual for exact values).
Hand-tighten the main mounting bolts initially—do not fully tighten them to retain adjustment allowance. Install the adjustment bracket bolts and hand-tighten them as well.
Apply medium-strength thread locker to the bolt threads (especially critical for vehicles with aluminum engine blocks) to prevent loosening due to long-term vibration.
Step 3: Install the Drive Belt
Refer to the belt routing diagram located in the engine bay (usually affixed inside the engine cover for Ford models, or in the appendix of the service manual for Volvo models) to confirm the routing sequence around the crankshaft pulley, alternator pulley, and tensioner pulley.
Use a dedicated belt tensioner tool to depress the tensioner, fit the drive belt onto all pulleys, and ensure the belt fully engages with the pulley grooves without misalignment or twisting.
Slowly release the tensioner to tension the belt to the specified deflection (press the middle of the belt—deflection should be 10–15 mm). Start the engine and let it idle; check for belt slippage or abnormal noise.
Step 4: Connect Electrical Wiring
Connect the alternator’s positive output cable (thick cable), tighten the terminal nut to a torque of 8–12 N·m, and fit the insulating protective cover to prevent short circuits.
Connect the alternator’s field wire connector (thin wires, usually a 2–3 pin connector), ensuring it clicks securely into place. For some models, a ground wire must also be connected.
Reconnect the negative battery cable.
Step 5: Final Tightening of Mounting Bolts
III. Post-installation Testing
Static Test: Turn off all electrical loads, measure the battery voltage with a multimeter—normal voltage ranges from 12.5 to 12.8 V.
Dynamic Test: Start the engine and let it idle; measure the battery voltage, which should stabilize at 13.8–14.5 V (indicating normal alternator output). Increase the engine speed to 2000 rpm—the voltage should remain within the above range without significant fluctuations.
Functional Test: Turn on high-power electrical devices (e.g., headlights, air conditioning, heater) and verify that the voltage stays above 13.5 V. Ensure there is no belt slippage, abnormal noise, unusual vibration, or burning odors from the alternator.
Key Installation Precautions for Ford/Volvo 12V Alternators
- These precautions are formulated based on OEM maintenance specifications and practical hands-on experience, covering core aspects including safety protection, installation precision, compatibility verification, and post-installation testing to ensure stable operation of the alternator after installation.
I. Pre-installation Safety and Compatibility Precautions
1. Power Disconnection Must Be Prioritized
Before installation, disconnect the negative battery cable without fail and wait for 5–10 minutes to discharge residual electricity in the vehicle’s electronic control system. Live operation is strictly prohibited. Failure to disconnect the battery may cause short circuits when plugging or unplugging alternator wiring, resulting in burnout of core components such as the alternator rectifier and vehicle ECU.
Before reconnecting the negative battery cable, ensure all wiring terminals are tight and free of exposed metal contacts.
2. Strict Verification of Part Compatibility
Only use OEM or OE-certified alternators that match the vehicle’s VIN. Alternator connectors, mounting hole positions, and power parameters vary significantly across different Ford and Volvo models. Non-genuine parts may lead to unstable voltage output, installation misalignment, and long-term damage to the battery and electrical equipment.
Inspect alternator accessories: Mounting bolts must comply with OEM specifications (high-strength bolts are required for some models); the drive belt model must match the number of grooves on the engine pulleys to prevent belt slippage or breakage.
3. Cleaning and Protection of the Mounting Position
Thoroughly clean oil stains, rust, and carbon deposits from the surface of the alternator mounting bracket, then apply a thin layer of anti-seize compound (especially critical for vehicles with aluminum engine blocks). This prevents bolt seizure caused by long-term exposure to high temperatures and vibrations, which would make subsequent disassembly difficult.
If there are coolant hoses or oil pipes near the mounting position, take protective measures in advance to avoid leakage due to collision during installation.
II. Installation Precision Control Precautions
1. Strictly Follow OEM Standards for Bolt Torque
The torque values for main mounting bolts, adjustment bracket bolts, and terminal nuts must comply with the vehicle-specific OEM service manual. The following reference ranges are for general guidance only—never apply them directly:
Ford models: Main mounting bolts 45–55 N·m; terminal nuts 8–10 N·m
Volvo models: Main mounting bolts 50–60 N·m; terminal nuts 10–12 N·m
Tighten bolts in the sequence of "from center to both sides" to avoid bracket deformation due to uneven stress. Use only medium-strength thread locker (e.g., Loctite 243)—high-strength thread locker may cause bolt breakage during disassembly.
2. Requirements for Drive Belt Installation and Tension
The belt routing must strictly follow the belt diagram in the engine bay (usually affixed inside the engine cover for Ford models, or included in the appendix of the service manual for Volvo models). Incorrect routing will cause reverse rotation of the alternator, power generation failure, or even damage to pulleys.
The belt tension must be precisely controlled: Manually press the middle of the belt, and the deflection should be 10–15 mm. For models equipped with automatic tensioners, check that the tensioner pointer is within the normal scale range after installation, with no deviation.
After installation, start the engine and let it idle. Observe that the belt runs without slippage, abnormal noise, or edge wear. Excessive tension will accelerate wear on the alternator bearing and tensioner, while insufficient tension will lead to slippage and inadequate power generation.
References:
- The two documents you have received, General Installation Method for Ford/Volvo 12V Alternators and Key Installation Precautions for Ford/Volvo 12V Alternators, are original compilations developed by me based on OEM maintenance specifications and hands-on practical experience. They are not direct excerpts from any single published document or official manual.
Supplementary Notes
- Content SourcesThe content integrates universal procedures, reference ranges for bolt torque, belt routing and tension requirements from Ford and Volvo Original Equipment Manufacturer Service Manuals (WSM). It also incorporates common safety protocols and fault prevention points summarized from practical operations, as well as industry-standard maintenance practices (e.g., power disconnection, application of anti-seize compound and thread locker) and testing criteria (static/dynamic voltage ranges).
- Reason for No "Standard Source Citation"WSMs for different model years and vehicle models specify unique installation steps and torque values. The versions provided here are generalized editions designed for quick on-site reference and operation. If you require precise, model-specific guidelines (e.g., for Ford Focus or Volvo XC60), you may provide the Vehicle Identification Number (VIN) or model year, and I can help locate the corresponding chapter and page number in the official WSM.
- Customization for Internal Use

