
Генератор 12V 150A TG15C075 для Mercedes-Benz
Применимый тип:Mercedes-Benz
Номер запчасти:124615028,TG15C075,2711540602,2711540802 E200 216 316,0124615028,CA1775IR,0124615042 ALB1775RB,ALB1775WA,A2711541002.A271154100280 LZL13500221218W 23285N, 0124615022,0124615028 271-154-06-02 271-154-08-02,2711541002 TG15C075, 0121540602 ,0124615022,0124615068 0124615028 063536150280 0986046300 2711541002,012-154-06-02,CAL10397AS,ALB1775 0986046300 0121540602 A2711541002,ALB1775GB 04852629AA,04862629AA,4852629AA,2711541002 DRB6300 116463
| Номинальный выход : | 12V 150A |
| Pulley : | 7PK 2cha |
| Размер : | |
| Вес : | Вес нетто 6,95 кг |
| Упаковочные материалы : | Нейтральная упаковка из крафт-бумаги |
| Спотовые / предварительные продажи : | presale |
| Гарантия : | 1 год |
| Номер продукта : |
| Тип : | генератор |
| Спецификация : | 12V 150A |
| Блок : | 7pk |
| Марка : | NUOJIN |
| Цифры : | 0124615022 |
| Качество : | НОВЫЙ |
| Время поставки : | 30 дней |








Overview of the TG15C075 Alternator
The TG15C075 alternator is a 12V, 150A unit built for Mercedes-Benz. It replaces the original assembly with the same mounting points, pulley offset and terminal layout, so the belt lines up and the existing wiring plugs in without modification.
Heat is the main enemy. The alternator sits in the airflow but also next to the exhaust manifold, and the diodes and regulator are the first parts to suffer when the under-bonnet temperature climbs.
Specifications at a Glance
- Rated voltage: 12V
- Rated output: 150 A
- Pulley: 7-groove PK
- Regulator: integrated, machine sensed
- Application: Mercedes-Benz
- Net weight: approximately 6.95 kg
- Condition: new, direct replacement for the original unit
The 12V, 150A rating is the output the unit holds at normal engine speed with the battery in a partially discharged state — the condition that matters in real use, not on a test bench.
Reference Numbers and Cross References
Cross references for this unit are listed below; use them as a matching aid rather than a substitute for checking the number on the old alternator:
- 0124615022
- 124615028
- TG15C075
- 2711540602
- 2711540802
- E200
- 0124615028
- CA1775IR
- 0124615042
- ALB1775RB
- ALB1775WA
- A2711541002.A271154100280
- LZL13500221218W
- 23285N
- 271-154-06-02
- 271-154-08-02
Where the label on the old unit has faded, compare the pulley groove count, the mounting ears and the plug shape with the photographs before ordering. This unit is listed with 16 references in total.
Application Notes
Mercedes-Benz models in this range share the same mounting bracket and belt layout, which is why one reference serves several years of production. Fitment is decided by the number on the unit, not by the model year alone.
Vehicles that have had an engine or accessory drive belt conversion may already carry a different alternator, so treat the catalogue as a starting point rather than the final answer.
What Wears Out First
Bearings carry the rotor at engine speed for the life of the vehicle. Once the front bearing dries out, the unit starts to whine, and the noise gets worse with electrical load rather than with engine speed alone.
Oil mist from a leaking cam or crank seal attacks the internal insulation. A unit that is oily on the outside is often already failing inside, even if the output still looks normal on a meter.
Signs of a Failing Alternator
- Slow cranking that gets worse each morning
- Dash lights that flicker at idle
- Radio interference or a hum through the speakers
- Alternator hot to the touch after a normal drive
- Charging voltage above 15V, boiling the battery
Check the belt first, then the battery earth, then the B+ cable. A slipping belt or a corroded earth produces the same dim-light symptom as a failing alternator and costs far less to fix.
What to Check Before Fitting
- Battery condition and earth strap
- Belt condition, alignment and tensioner travel
- Pulley groove count against the original unit
- Regulator plug shape and B+ terminal size
- Charging voltage after fitting, at idle and at 2000 rpm
A new alternator on a tired battery or a glazed belt will not restore charging. Test the simple items before the unit goes on.
Fitting the Replacement
With the battery isolated, relieve the belt tension, disconnect the B+ terminal and unplug the regulator connector, then remove the mounting bolts and lift the unit out.
Fit the replacement, reconnect the plug and B+ cable, then refit the belt and set tension to specification. Start the engine and confirm charging voltage at idle before the first drive.
Quality Control and Supply from Hejian Nuojin Auto Parts Co., Ltd.
Hejian Nuojin Auto Parts Co., Ltd. produces starter and alternator components for the aftermarket. Each alternator is tested for output at idle and rated speed, ripple current, regulator voltage and bearing noise before packing.
Common references are held in stock, volume orders ship in around 30 days and every unit carries a one-year warranty against manufacturing defects.
Frequently Asked Questions
Can I replace the regulator only?
Yes, when the bearings and diodes are sound. On a high-mileage unit the complete alternator is usually better value.
Does the alternator come with a pulley?
Yes, the unit is supplied with its pulley fitted as shown in the photographs, so the original belt can be reused.
Can a bad alternator damage the battery?
Overcharging or heavy ripple will shorten battery life, and a deeply discharged battery can fail. Replace the alternator before the battery if voltage is out of range.
What charging voltage should I see?
Around 13.8 to 14.7V at idle on a 12V system, and about 27.5 to 28.5V on a 24V system, measured at the battery posts.

