
Генератор 12V 150A ALN3661DD для Lexus NX 200t 2.0
Применимый тип:Lexus NX 200t 2.0
Номер запчасти: 2706036101 1042117080.1042118860.142118861 ALN3661DD 27060-361 01
| Номинальный выход : | 12V 150A |
| Pulley : | 6PK |
| Размер : | 24*18*17single unit inner box |
| Вес : | |
| Упаковочные материалы : | Нейтральная упаковка из крафт-бумаги |
| Спотовые / предварительные продажи : | В наличии |
| Гарантия : | 1 год |
| Номер продукта : |
| Тип : | Automobile generator |
| Спецификация : | 12V 150A |
| Блок : | 6PK |
| Марка : | NUOJIN |
| Цифры : | 2706036101 |
| Качество : | НОВЫЙ |
| Время поставки : | 10 дней |





Overview of the ALN3661DD Alternator
This ALN3661DD alternator is the 12V, 150A replacement for Lexus NX 200t 2.0 applications. The housing, pivot points and B+ terminal follow the original design, which means the unit drops into the existing bracket and reuses the factory belt.
An alternator spends its life at engine speed, so bearings, slip rings and diodes wear continuously rather than in bursts. That is why output falls gradually and why the first symptom is often a battery that is flat only after a few days of short trips.
Specification Summary
- Rated voltage: 12V
- Rated output: 150 A
- Pulley: 6-groove PK
- Regulator: integrated, machine sensed
- Application: Lexus NX 200t 2.0
- Condition: new, direct replacement for the original unit
The 12V, 150A rating is the output the unit holds at normal engine speed with the battery in a partially discharged state — the condition that matters in real use, not on a test bench.
Reference Numbers and Cross References
The alternator is supplied against the following references, which help identify it against the unit already fitted to the vehicle:
- 2706036101
- ALN3661DD
- 27060-361
Cross references are a guide, not a fitment guarantee. The same engine was often built with more than one alternator, and the pulley type or terminal position can differ between them. This unit is listed with 3 references in total.
Where This Alternator Fits
Lexus NX 200t 2.0 models in this range share the same mounting bracket and belt layout, which is why one reference serves several years of production. Fitment is decided by the number on the unit, not by the model year alone.
If the number on the old alternator falls outside the list above, send the engine code and a photograph of the rear cover before ordering. A unit with the right housing but a different regulator plug will not connect cleanly.
What Wears Out First
Bearings carry the rotor at engine speed for the life of the vehicle. Once the front bearing dries out, the unit starts to whine, and the noise gets worse with electrical load rather than with engine speed alone.
The diode rectifier is usually the first casualty. Six diodes convert the AC output to DC, and when one fails the alternator still charges but with a ripple that upsets the battery and the vehicle electronics.
What to Look For
- Battery light on with the engine running
- Dim or pulsing interior lights
- Voltage at the battery below 13.5V with the engine idling
- Belt squeal that appears when a heavy load switches on
- Overheating alternator body after a short run
A load test separates a tired alternator from a tired battery. Switch on the lights, blower and rear demister and watch the voltage: a healthy unit holds its output, a worn one sags.
Pre-Fit Checklist
- Battery condition and earth strap
- Belt condition, alignment and tensioner travel
- Pulley groove count against the original unit
- Regulator plug shape and B+ terminal size
- Charging voltage after fitting, at idle and at 2000 rpm
A new alternator on a tired battery or a glazed belt will not restore charging. Test the simple items before the unit goes on.
Fitting the Replacement
With the battery isolated, relieve the belt tension, disconnect the B+ terminal and unplug the regulator connector, then remove the mounting bolts and lift the unit out.
Refit the belt and check alignment, reconnect the terminals and confirm charging voltage at idle and at 2000 rpm. Re-check belt tension after the first heat cycle.
Quality Control and Supply from Hejian Nuojin Auto Parts Co., Ltd.
Every batch is inspected for housing dimensions, pulley alignment and terminal integrity, and each unit is bench tested for output, ripple and regulator cut-in before it is boxed in neutral cartons with foam protection.
Standard references are kept as spot goods, volume orders are delivered in around 30 days and each alternator carries a one-year warranty against manufacturing defects.
Frequently Asked Questions
Does the alternator come with a pulley?
Yes, the unit is supplied with its pulley fitted as shown in the photographs, so the original belt can be reused.
Can a bad alternator damage the battery?
Overcharging or heavy ripple will shorten battery life, and a deeply discharged battery can fail. Replace the alternator before the battery if voltage is out of range.
What charging voltage should I see?
Around 13.8 to 14.7V at idle on a 12V system, and about 27.5 to 28.5V on a 24V system, measured at the battery posts.
Why does the battery light glow at idle?
Usually a worn regulator, a slipping belt or a diode fault. Check belt tension and charging voltage before replacing the unit.
Installation Method of 12V Alternator for Lexus (Mainstream Gasoline Models, Excluding Hybrid)
Pre-installation Preparation (Safety and Compatibility First)
1. Vehicle and Part Compatibility Check
2. Tools and Consumables Preparation
Tools: socket wrench, ratchet wrench, torque wrench, screwdriver, wire terminal crimping tool, jack with safety stands, safety goggles, work gloves.
Consumables: insulating tape, rust inhibitor, thread locker (as required). A belt tension gauge is recommended.
3. Vehicle Safety Measures
4. Space Preparation and Protection
Installation Steps (Follow in Sequence)
- Alternator Placement and Preliminary FixationPlace the alternator onto the mounting bracket and align it with the upper/lower and front/rear mounting holes. Install the fixing bolts and nuts (typically upper bolts and lower nuts) but do not fully tighten them—leave slight adjustability to facilitate subsequent belt tension adjustment. Ensure the axes of the alternator pulley, crankshaft pulley, idler pulley, and tensioner pulley are parallel with no deviation.
- Electrical Wiring Connection (Perform with Power Off)
First, connect the thick positive output cable and tighten the terminal nut to the reference torque of approximately 10 N·m; insulate the connection properly.
Then, plug in the field wire/signal wire connector, ensuring it locks into place securely and verifying that the pins match the correct configuration.
Inspect all connections to confirm there are no loose terminals or exposed wires. Secure the wire harnesses with clips and keep them away from high-temperature or moving components.
- Drive Belt Installation and Tension Adjustment
Route the drive belt into the grooves of all pulleys according to the diagram marked in the engine compartment.
For models with automatic tensioners: Release the tensioner using a dedicated tool, fit the belt into place, and confirm that the tensioner pointer returns to the standard scale range after resetting.
For models with manual tensioners: Use a tool or gently pry the alternator (applying force only on the reinforced ribs of the housing) to tension the belt. Press the middle section of the belt—the deflection should be approximately 10–15 mm, or measure the tension to the standard value using a belt tension gauge.
Tighten the alternator fixing bolts and nuts to the torque specified in the repair manual (common values: upper bolts 40–58 N·m, lower nuts 34–54 N·m—always refer to the manual for your specific model year).
- Final Assembly and Power-on Test
Reinstall all removed components, including the lower engine guard, wheel arch liner, and engine cover.
Reconnect the negative battery cable.
Start the engine and observe the alternator operation: no abnormal noise, no belt slipping or squealing.
Use a multimeter to measure the battery voltage: the voltage should be 13.5–14.5 V at idle speed, and remain stable without significant fluctuations when the engine speed is increased to around 2000 r/min. Verify that the charging indicator light turns off after startup.
Turn on high-power loads such as headlights and air conditioning—the voltage should remain stable within the range of 13.0–14.5 V.
Precautions for Installation of 12V Alternator for Lexus
I. Electrical Safety Specifications
1. Full Power-off Operation Throughout the Process
2. Prohibition of Live-line Operations
3. Absolute Polarity Correctness
4. Wiring Insulation and Securing
II. Mechanical Installation Accuracy Requirements
1. Strict Compliance with Fastening Torque Specifications
2. Precise Control of Drive Belt Tension
For models with automatic tensioners: Use a dedicated tool to release the tensioner; avoid rough operation that could cause tensioner failure. After fitting the belt, confirm that the tensioner pointer falls within the standard scale range, with no belt twisting or edge detachment.
For models with manual tensioners: Press the middle section of the belt—the deflection should be controlled within 10–15 mm. Alternatively, use a belt tension gauge to measure the tension, ensuring the reading meets the standards for the specific vehicle model.
References:
Official Source and Basis
The Lexus/Toyota Genuine Repair Manual (RM Series) is categorized by model year, chassis number, and engine type (e.g., 2GR-FE, 8AR-FTS). It contains precise parameters including bolt torque values, belt specifications, and circuit definitions. In this compilation, universal installation steps and typical parameter values are extracted to facilitate quick and straightforward application.
To verify the original content, you may consult the RM Manual corresponding to your Lexus model year at an authorized Lexus dealership or after-sales service center. Alternatively, subscribe to or purchase the electronic version via the Toyota Technical Information System (TIS) and search for the chapter titled Charging System — Alternator Assembly for cross-checking.
Industry Standards and Testing Specifications
Procedures such as disconnecting the negative battery terminal, adjusting drive belt tension, and conducting voltage tests are universal safety and quality requirements for disassembling and assembling automotive electrical components and engine accessories. These standards apply to alternator replacement for the vast majority of passenger vehicles.
Parameters such as the idle voltage range of 13.5–14.5V and the drive belt mid-span deflection of 10–15mm are common industry testing and adjustment benchmarks. For precise values, always refer to the repair manual specific to your vehicle’s model year.

