
Генератор 12V 40A GE01-18-300 для Nissan
Применимый тип:Nissan
Номер запчасти:23100-06T10 UD11287A 0986035411 110264 CAL20170AS LR135133. LR13544,LR13570,LR13570B,LR13574B GE01-18-300 2310001B00.2310001B05.2310001B10, 2310001B15 A001T22071,A001T22971, A001T22975.A001T24371 2310003B00.2310003B05, 2310006T10.2310010110 23100-27G00 23100-27G10 23100-H7700 DRA5411 JA105IR LR135107,LR135108,LR135132 LR13586F.LR13801,LR140132.LR140133 8941538821 LRA441 943356937010,944390511350 GE0118300 3446818200.3446828100.3446828200. A001T02871 ALH2288LK,ALM2288BS,ALM2288NW, ALN6288NW 1248077201 436507 436505
| Номинальный выход : | 12V 40A |
| Pulley : | 1PK |
| Размер : | |
| Вес : | Вес: Net weight: 3.2 |
| Упаковочные материалы : | Нейтральная упаковка из крафт-бумаги |
| Спотовые / предварительные продажи : | В наличии |
| Гарантия : | 1 год |
| Номер продукта : |
| Тип : | генератор |
| Спецификация : | 12V 40A |
| Блок : | 1PK |
| Марка : | NUOJIN |
| Цифры : | GE01-18-300 |
| Качество : | НОВЫЙ |
| Время поставки : | 30 дней |






Overview of the GE01-18-300 Alternator
This GE01-18-300 alternator is the 12V, 40A replacement for Nissan applications. The housing, pivot points and B+ terminal follow the original design, which means the unit drops into the existing bracket and reuses the factory belt.
Heat is the main enemy. The alternator sits in the airflow but also next to the exhaust manifold, and the diodes and regulator are the first parts to suffer when the under-bonnet temperature climbs.
Technical Summary
- Rated voltage: 12V
- Rated output: 40 A
- Pulley: 1-groove PK
- Regulator: integrated, machine sensed
- Application: Nissan
- Net weight: approximately 3.2 kg
- Condition: new, direct replacement for the original unit
The 12V, 40A rating is the output the unit holds at normal engine speed with the battery in a partially discharged state — the condition that matters in real use, not on a test bench.
Reference Numbers and Cross References
The OEM and aftermarket references listed for this alternator are:
- GE01-18-300
- 23100-06T10
- UD11287A
- 0986035411
- 110264
- LR135133
- LR13544
- LR13570
- LR13570B
- LR13574B
- 2310001B15
- A001T22971
- A001T22975.A001T24371
- 2310003B00.2310003B05
- 2310006T10.2310010110
- 23100-27G00
Cross references are a guide, not a fitment guarantee. The same engine was often built with more than one alternator, and the pulley type or terminal position can differ between them. This unit is listed with 16 references in total.
Where This Alternator Fits
This alternator family was fitted across a range of Nissan applications as engines and electrical loads were revised. The unit here covers the references above and is a direct replacement where those numbers match.
Vehicles that have had an engine or accessory drive belt conversion may already carry a different alternator, so treat the catalogue as a starting point rather than the final answer.
How This Alternator Fails
The diode rectifier is usually the first casualty. Six diodes convert the AC output to DC, and when one fails the alternator still charges but with a ripple that upsets the battery and the vehicle electronics.
Oil mist from a leaking cam or crank seal attacks the internal insulation. A unit that is oily on the outside is often already failing inside, even if the output still looks normal on a meter.
Signs of a Failing Alternator
- Slow cranking that gets worse each morning
- Dash lights that flicker at idle
- Radio interference or a hum through the speakers
- Alternator hot to the touch after a normal drive
- Charging voltage above 15V, boiling the battery
Check the belt first, then the battery earth, then the B+ cable. A slipping belt or a corroded earth produces the same dim-light symptom as a failing alternator and costs far less to fix.
What to Check Before Fitting
- Battery state of charge and age
- Condition of the B+ cable and its fuse
- Pulley type: solid, clutch or overrunning
- Mounting ear dimensions against the bracket
- Belt routing after the new unit is fitted
A new alternator on a tired battery or a glazed belt will not restore charging. Test the simple items before the unit goes on.
Installation Notes
Disconnect the battery negative terminal first, then release the belt tension and slip the belt off the pulley. Remove the B+ cable and the regulator plug before the mounting bolts.
Fit the replacement, reconnect the plug and B+ cable, then refit the belt and set tension to specification. Start the engine and confirm charging voltage at idle before the first drive.
Quality Control and Supply from Hejian Nuojin Auto Parts Co., Ltd.
Hejian Nuojin Auto Parts Co., Ltd. produces starter and alternator components for the aftermarket. Each alternator is tested for output at idle and rated speed, ripple current, regulator voltage and bearing noise before packing.
Common references are held in stock, volume orders ship in around 30 days and every unit carries a one-year warranty against manufacturing defects.
Frequently Asked Questions
Can a bad alternator damage the battery?
Overcharging or heavy ripple will shorten battery life, and a deeply discharged battery can fail. Replace the alternator before the battery if voltage is out of range.
Can I replace the regulator only?
Yes, when the bearings and diodes are sound. On a high-mileage unit the complete alternator is usually better value.
What charging voltage should I see?
Around 13.8 to 14.7V at idle on a 12V system, and about 27.5 to 28.5V on a 24V system, measured at the battery posts.
Why does the battery light glow at idle?
Usually a worn regulator, a slipping belt or a diode fault. Check belt tension and charging voltage before replacing the unit.
Installation Method for Nissan 12V Alternator
I. Pre-Installation Preparation
Confirm that the alternator model is compatible with the Nissan vehicle, and verify the voltage (12V) and mounting hole dimensions.
Prepare tools: socket wrench, torque wrench, belt tensioner, wire crimpers, insulating tape, etc.
Disconnect the negative terminal of the vehicle battery to avoid short circuits during installation.
II. Specific Installation Steps
1. Positioning and Fixing
Place the alternator on the mounting bracket in the engine compartment and align it with the bolt holes.
Temporarily fasten the alternator with bolts (do not fully tighten) to reserve adjustment space.
2. Wiring Connection
Connect the alternator output terminal (B+ terminal) to the positive terminal of the battery using a dedicated wiring terminal and secure it tightly.
Connect the field wire (F terminal) to the corresponding interface of the voltage regulator, ensuring the plug is fully inserted and secure.
Connect the ground wire (G terminal) to the engine block to ensure good grounding.
3. Belt Assembly and Tensioning
Install the drive belt and adjust the alternator position to achieve proper belt tension.
Use a torque wrench to tighten the mounting bolts to the manufacturer's specified torque. Then check the tension with a belt tensioner (the deflection at the midpoint of the belt should be approximately 10-15mm when pressed).
4. Commissioning and Inspection
Reconnect the negative terminal of the battery, start the engine, and observe if the alternator operates smoothly.
Use a multimeter to measure the output voltage; the normal range at idle speed is 13.5-14.5V.
Check for belt slipping, wire overheating, or abnormal noises. Complete the installation only after confirming no abnormalities.
III. Key Notes
Strictly distinguish the functions of each terminal during wiring to avoid reverse connection, which may burn out the alternator or regulator.
The tightening torque of the bolts must comply with the requirements in the Nissan vehicle maintenance manual; both loose and over-tightened bolts will affect performance.
Conduct a load test after installation to ensure the alternator outputs stably at different speeds.
Key Notes for Installation of Nissan 12V Alternator
I. Electrical Connection Notes
Disconnect the negative terminal of the battery before wiring to prevent short circuits that could burn out the alternator or vehicle electrical components.
Strictly distinguish the functions of each terminal: connect the B+ terminal to the positive terminal of the battery, the F terminal to the regulator, and the G terminal to the ground. Reverse connection or incorrect wiring is strictly prohibited.
Ensure the wiring terminals are clean and free of oxidation. Wrap them with insulating tape after connection to guarantee good contact and reliable insulation.
II. Mechanical Installation Notes
The alternator model must be fully compatible with the Nissan vehicle. Verify that the mounting hole positions and pulley dimensions match.
Tighten the fixing bolts to the torque specified by the manufacturer. Avoid loose bolts that cause operational vibration or over-tightened bolts that damage the bracket.
Adjust the belt tension to an appropriate level. Excessively loose belts easily slip and reduce power generation efficiency, while overly tight belts accelerate bearing wear.
III. Commissioning and Safety Notes
After starting the engine, first check the alternator for abnormal noise, vibration, or odor. Stop the engine immediately for inspection if any abnormalities are found.
Use a multimeter to measure the output voltage. Maintain 13.5-14.5V at idle speed, with fluctuations not exceeding ±0.5V under load.
Avoid tools touching the alternator rotor and stator windings during installation to prevent component damage.
IV. Post-Installation Usage Notes
Regularly check the belt tension and wiring terminal status in the short term after installation. Tighten any loose parts promptly.
Avoid long-term overloaded operation of the alternator to extend its service life.
If the alternator fails to generate electricity or has abnormal voltage, first inspect the wiring connections before checking internal components.
References:

