
Генератор 12V 35A LR135-95 для Mazda, Yangma C240 forklifts
Применимый тип:Mazda/Yangma C240 forklifts
Номер запчасти:LR135-95 LR135105 LR12015C LR135115 LR135116 LR135118 LR135124 LR135126 LR135127 LR135128 LR13561B, LR13574C, LR13586, LR13586C, LR13595, D50118300, F85118300, 65812003380, 65812003380A, 481018300 A001T31699, A001T33277, A1T03476, A1T23377 482818300, D40118300, D40118300A,LR13531, LR13558 LR135-115 A1T25077 A001T25083, A001T25087, A1T25077 A1T31685
| Номинальный выход : | 12V 35A |
| Pulley : | |
| Размер : | 24*18*17single unit inner box |
| Вес : | Вес нетто 3,35 кг |
| Упаковочные материалы : | Нейтральная упаковка из крафт-бумаги |
| Спотовые / предварительные продажи : | В наличии |
| Гарантия : | 1 год |
| Номер продукта : |
| Тип : | генератор |
| Спецификация : | 12V 35A |
| Блок : | |
| Марка : | NUOJIN |
| Цифры : | LR135-95 5-81200341-1 |
| Качество : | НОВЫЙ |
| Время поставки : | 10 дней |



Overview of the LR135-95 Alternator
The LR135-95 is a 12V, 35A alternator for Mazda, Yangma C240 forklifts. It is a claw-pole machine with an integrated regulator, balanced at the factory so it runs quietly at idle and at speed.
An alternator spends its life at engine speed, so bearings, slip rings and diodes wear continuously rather than in bursts. That is why output falls gradually and why the first symptom is often a battery that is flat only after a few days of short trips.
Specification Summary
- Rated voltage: 12V
- Rated output: 35 A
- Regulator: integrated, machine sensed
- Application: Mazda, Yangma C240 forklifts
- Net weight: approximately 3.35 kg
- Condition: new, direct replacement for the original unit
The 12V, 35A rating is the output the unit holds at normal engine speed with the battery in a partially discharged state — the condition that matters in real use, not on a test bench.
Reference Numbers and Cross References
The alternator is supplied against the following references, which help identify it against the unit already fitted to the vehicle:
- LR135-95
- LR135105
- LR135115
- LR135116
- LR135118
- C240
- LR135124
- LR135126
- LR135127
- LR135128
- LR13561B
- LR13574C
- LR13586
- LR13586C
- LR13595
- D50118300
Where the label on the old unit has faded, compare the pulley groove count, the mounting ears and the plug shape with the photographs before ordering. This unit is listed with 16 references in total.
Matching the Unit to the Vehicle
Mazda, Yangma C240 forklifts models in this range share the same mounting bracket and belt layout, which is why one reference serves several years of production. Fitment is decided by the number on the unit, not by the model year alone.
If the number on the old alternator falls outside the list above, send the engine code and a photograph of the rear cover before ordering. A unit with the right housing but a different regulator plug will not connect cleanly.
How This Alternator Fails
The diode rectifier is usually the first casualty. Six diodes convert the AC output to DC, and when one fails the alternator still charges but with a ripple that upsets the battery and the vehicle electronics.
The regulator controls field current and therefore output voltage. Its brushes ride on the slip rings, and both wear. A worn regulator shows up as a charging voltage that drifts or flickers with engine speed.
What to Look For
- Slow cranking that gets worse each morning
- Dash lights that flicker at idle
- Radio interference or a hum through the speakers
- Alternator hot to the touch after a normal drive
- Charging voltage above 15V, boiling the battery
Check the belt first, then the battery earth, then the B+ cable. A slipping belt or a corroded earth produces the same dim-light symptom as a failing alternator and costs far less to fix.
Checks Before Installation
- Battery state of charge and age
- Condition of the B+ cable and its fuse
- Pulley type: solid, clutch or overrunning
- Mounting ear dimensions against the bracket
- Belt routing after the new unit is fitted
Most charging comebacks trace back to a battery or belt problem that was already there. Check those two first, then fit the alternator once and correctly.
Fitting the Replacement
Disconnect the battery negative terminal first, then release the belt tension and slip the belt off the pulley. Remove the B+ cable and the regulator plug before the mounting bolts.
Refit the belt and check alignment, reconnect the terminals and confirm charging voltage at idle and at 2000 rpm. Re-check belt tension after the first heat cycle.
Quality Control and Supply from Hejian Nuojin Auto Parts Co., Ltd.
Hejian Nuojin Auto Parts Co., Ltd. produces starter and alternator components for the aftermarket. Each alternator is tested for output at idle and rated speed, ripple current, regulator voltage and bearing noise before packing.
Common references are held in stock, volume orders ship in around 30 days and every unit carries a one-year warranty against manufacturing defects.
Frequently Asked Questions
What charging voltage should I see?
Around 13.8 to 14.7V at idle on a 12V system, and about 27.5 to 28.5V on a 24V system, measured at the battery posts.
Why does the battery light glow at idle?
Usually a worn regulator, a slipping belt or a diode fault. Check belt tension and charging voltage before replacing the unit.
Does the alternator come with a pulley?
Yes, the unit is supplied with its pulley fitted as shown in the photographs, so the original belt can be reused.
Can a bad alternator damage the battery?
Overcharging or heavy ripple will shorten battery life, and a deeply discharged battery can fail. Replace the alternator before the battery if voltage is out of range.

