
Генератор 12V 90A 37300-4X301 для Kia
Применимый тип:Kia
Номер запчасти:37300-4X301 373004X300 373004X250 373004X301, 373004X310, 373004X350, 373004X351 ALY6172DD, ALY6172KL, ALY6172KR, ALY6172LK 021319160, 021319172, 021319391 301N20431Z
| Номинальный выход : | 12V 90A |
| Pulley : | 5PK |
| Размер : | |
| Вес : | Вес нетто 7,05 кг |
| Упаковочные материалы : | Нейтральная упаковка из крафт-бумаги |
| Спотовые / предварительные продажи : | В наличии |
| Гарантия : | 1 год |
| Номер продукта : |
| Тип : | генератор |
| Спецификация : | 12V 90A |
| Блок : | 5PK |
| Марка : | NUOJIN |
| Цифры : | 37300-4X301 373004X300 |
| Качество : | НОВЫЙ |
| Время поставки : | 30 дней |







Overview of the 37300-4X301 Alternator
For Kia owners chasing a battery light or a slowly flattening battery, the 37300-4X301 is a 12V, 90A alternator supplied as a complete unit with its regulator and rectifier already fitted.
Heat is the main enemy. The alternator sits in the airflow but also next to the exhaust manifold, and the diodes and regulator are the first parts to suffer when the under-bonnet temperature climbs.
Specifications at a Glance
- Rated voltage: 12V
- Rated output: 90 A
- Pulley: 5-groove PK
- Regulator: integrated, machine sensed
- Application: Kia
- Net weight: approximately 7.05 kg
- Condition: new, direct replacement for the original unit
The 12V, 90A rating is the output the unit holds at normal engine speed with the battery in a partially discharged state — the condition that matters in real use, not on a test bench.
Reference Numbers and Cross References
Cross references for this unit are listed below; use them as a matching aid rather than a substitute for checking the number on the old alternator:
- 37300-4X301
- 373004X300
- 373004X250
- 373004X301
- 373004X310
- 373004X350
- 373004X351
- ALY6172DD
- ALY6172KL
- ALY6172KR
- ALY6172LK
Where the label on the old unit has faded, compare the pulley groove count, the mounting ears and the plug shape with the photographs before ordering. This unit is listed with 11 references in total.
Matching the Unit to the Vehicle
This alternator family was fitted across a range of Kia applications as engines and electrical loads were revised. The unit here covers the references above and is a direct replacement where those numbers match.
Vehicles that have had an engine or accessory drive belt conversion may already carry a different alternator, so treat the catalogue as a starting point rather than the final answer.
Common Failure Modes
The regulator controls field current and therefore output voltage. Its brushes ride on the slip rings, and both wear. A worn regulator shows up as a charging voltage that drifts or flickers with engine speed.
Bearings carry the rotor at engine speed for the life of the vehicle. Once the front bearing dries out, the unit starts to whine, and the noise gets worse with electrical load rather than with engine speed alone.
Signs of a Failing Alternator
- Slow cranking that gets worse each morning
- Dash lights that flicker at idle
- Radio interference or a hum through the speakers
- Alternator hot to the touch after a normal drive
- Charging voltage above 15V, boiling the battery
A load test separates a tired alternator from a tired battery. Switch on the lights, blower and rear demister and watch the voltage: a healthy unit holds its output, a worn one sags.
What to Check Before Fitting
- Battery condition and earth strap
- Belt condition, alignment and tensioner travel
- Pulley groove count against the original unit
- Regulator plug shape and B+ terminal size
- Charging voltage after fitting, at idle and at 2000 rpm
Most charging comebacks trace back to a battery or belt problem that was already there. Check those two first, then fit the alternator once and correctly.
Installation Notes
With the battery isolated, relieve the belt tension, disconnect the B+ terminal and unplug the regulator connector, then remove the mounting bolts and lift the unit out.
Fit the replacement, reconnect the plug and B+ cable, then refit the belt and set tension to specification. Start the engine and confirm charging voltage at idle before the first drive.
Quality Control and Supply from Hejian Nuojin Auto Parts Co., Ltd.
Every batch is inspected for housing dimensions, pulley alignment and terminal integrity, and each unit is bench tested for output, ripple and regulator cut-in before it is boxed in neutral cartons with foam protection.
Common references are held in stock, volume orders ship in around 30 days and every unit carries a one-year warranty against manufacturing defects.
Frequently Asked Questions
Why does the battery light glow at idle?
Usually a worn regulator, a slipping belt or a diode fault. Check belt tension and charging voltage before replacing the unit.
Can I replace the regulator only?
Yes, when the bearings and diodes are sound. On a high-mileage unit the complete alternator is usually better value.
What charging voltage should I see?
Around 13.8 to 14.7V at idle on a 12V system, and about 27.5 to 28.5V on a 24V system, measured at the battery posts.
Does the alternator come with a pulley?
Yes, the unit is supplied with its pulley fitted as shown in the photographs, so the original belt can be reused.
Applicable Models Model Years Engine Code Displacement Power Body Type
Model: Imported KIA BONGO Bus 2.9 TDiC 4WD Years: 2003–Onwards Engine Code: HJ3 Displacement: 2902 cc Power: 90 kW Body Type: Bus
Model: Imported KIA BONGO Platform/Chassis (PU) 2.9 TDiC Years: 2003–Onwards Engine Code: HJ3 Displacement: 2902 cc Power: 90 kW Body Type: Platform/Chassis
Model: Imported KIA BONGO Platform/Chassis (PU) 2.9 TDiC 4WD Years: 2003–Onwards Engine Code: HJ3 Displacement: 2902 cc Power: 90 kW Body Type: Platform/Chassis
Model: Imported KIA BONGO Van 2.9 TDiC Years: 2003–Onwards Engine Code: HJ3 Displacement: 2902 cc Power: 90 kW Body Type: Van
Model: Imported KIA BONGO Van 2.9 TDiC All-wheel Drive Years: 2003–Onwards Engine Code: HJ3 Displacement: 2902 cc Power: 90 kW Body Type: Van

