
Генератор 24V 55A UD12123A для JCB DIESELMAX
Применимый тип:JCB DIESELMAX
Номер запчасти:32008650 A9196 UD12123A 115899 11203441 11203913 11203993 11204116 11204920 AAK558 ,AAK577 AAK5787 AAK58 AAK5885 IA121 IA1469 32008611 32008650 32008678 32008678S KRAUFALI2469LK ALI2469SK ALI5584LK ALI55840LP 301N21856Z 301N22033Z ALI5584UX ALI5584YX MG623 MG6 ALI2469WA ZAUFER ALI5584WA
| Номинальный выход : | 24V 55A |
| Pulley : | 8pk |
| Размер : | 24*18*17single unit inner box |
| Вес : | |
| Упаковочные материалы : | Нейтральная упаковка из крафт-бумаги |
| Спотовые / предварительные продажи : | В наличии |
| Гарантия : | 1 год |
| Номер продукта : |
| Тип : | генератор |
| Спецификация : | 24V 55A |
| Блок : | 8pk |
| Марка : | nuojin |
| Цифры : | 32008650 32008611 |
| Качество : | НОВЫЙ |
| Время поставки : | 10 дней |





Overview of the UD12123A Alternator
The UD12123A alternator is a 24V, 55A unit built for JCB DIESELMAX. It replaces the original assembly with the same mounting points, pulley offset and terminal layout, so the belt lines up and the existing wiring plugs in without modification.
Heat is the main enemy. The alternator sits in the airflow but also next to the exhaust manifold, and the diodes and regulator are the first parts to suffer when the under-bonnet temperature climbs.
Specification Summary
- Rated voltage: 24V
- Rated output: 55 A
- Pulley: 8-groove PK
- Regulator: integrated, machine sensed
- Application: JCB DIESELMAX
- Condition: new, direct replacement for the original unit
The 24V, 55A rating is the output the unit holds at normal engine speed with the battery in a partially discharged state — the condition that matters in real use, not on a test bench.
Reference Numbers and Cross References
The alternator is supplied against the following references, which help identify it against the unit already fitted to the vehicle:
- A9196
- UD12123A
- 115899
- AAK558
- AAK577
- AAK5787
- AAK58
- AAK5885
- IA121
- IA1469
- KRAUFALI2469LK
- ALI2469SK
- ALI5584LK
- ALI55840LP
- 301N21856Z
- ALI5584UX
Where the label on the old unit has faded, compare the pulley groove count, the mounting ears and the plug shape with the photographs before ordering. This unit is listed with 16 references in total.
Where This Alternator Fits
This alternator family was fitted across a range of JCB applications as engines and electrical loads were revised. The unit here covers the references above and is a direct replacement where those numbers match.
If the number on the old alternator falls outside the list above, send the engine code and a photograph of the rear cover before ordering. A unit with the right housing but a different regulator plug will not connect cleanly.
How This Alternator Fails
The diode rectifier is usually the first casualty. Six diodes convert the AC output to DC, and when one fails the alternator still charges but with a ripple that upsets the battery and the vehicle electronics.
Oil mist from a leaking cam or crank seal attacks the internal insulation. A unit that is oily on the outside is often already failing inside, even if the output still looks normal on a meter.
Fault Symptoms
- Battery warning lamp glowing at idle and fading at speed
- Headlights that brighten when the engine is revved
- Battery flat after a few days of short trips
- Whine or rumble that rises with electrical load
- Burning smell from the alternator after a long drive
A load test separates a tired alternator from a tired battery. Switch on the lights, blower and rear demister and watch the voltage: a healthy unit holds its output, a worn one sags.
Checks Before Installation
- Battery condition and earth strap
- Belt condition, alignment and tensioner travel
- Pulley groove count against the original unit
- Regulator plug shape and B+ terminal size
- Charging voltage after fitting, at idle and at 2000 rpm
Most charging comebacks trace back to a battery or belt problem that was already there. Check those two first, then fit the alternator once and correctly.
Fitting the Replacement
Disconnect the battery negative terminal first, then release the belt tension and slip the belt off the pulley. Remove the B+ cable and the regulator plug before the mounting bolts.
Refit the belt and check alignment, reconnect the terminals and confirm charging voltage at idle and at 2000 rpm. Re-check belt tension after the first heat cycle.
Quality Control and Supply from Hejian Nuojin Auto Parts Co., Ltd.
Every batch is inspected for housing dimensions, pulley alignment and terminal integrity, and each unit is bench tested for output, ripple and regulator cut-in before it is boxed in neutral cartons with foam protection.
Common references are held in stock, volume orders ship in around 30 days and every unit carries a one-year warranty against manufacturing defects.
Frequently Asked Questions
Can a bad alternator damage the battery?
Overcharging or heavy ripple will shorten battery life, and a deeply discharged battery can fail. Replace the alternator before the battery if voltage is out of range.
Can I replace the regulator only?
Yes, when the bearings and diodes are sound. On a high-mileage unit the complete alternator is usually better value.
Does the alternator come with a pulley?
Yes, the unit is supplied with its pulley fitted as shown in the photographs, so the original belt can be reused.
Why does the battery light glow at idle?
Usually a worn regulator, a slipping belt or a diode fault. Check belt tension and charging voltage before replacing the unit.

