
Стартер 12V 4.5KW 13T 104452A1 для 6BT3.9
Применимый тип:6BT3.9
Номер запчасти: 228000-0216 104452A1 3904466 3920403 3964432,128000-0210,128000-0213 3675154,3920403,3964427,3920643 STG92845 3964427 1308066H91 1308066H91 1280000212 1280000215 3904466 3957594
| Мощность л.с. : | 12V 4.5KW |
| Число футов : | 13T |
| Размер : | 24*12*16single unit inner box |
| Вес : | Вес нетто 7,6 кг |
| Упаковочные материалы : | Нейтральная упаковка из крафт-бумаги |
| Спотовые / предварительные продажи : | В наличии |
| Гарантия : | 1 год |
| Номер продукта : |
| Тип : | стартер |
| Спецификация : | 12V 4.5KW |
| Число футов : | 13T |
| Марка : | NUOJIN |
| Цифры : | 228000-0216 |
| Качество : | НОВЫЙ |
| Время поставки : | 30 дней |












Overview of the 104452A1 Starter Motor
The 104452A1 starter motor is a 12V, 4.5 kW unit built for 6BT3.9. It is a reduction-gear starter with a pre-engaged solenoid, assembled to the original mounting flange and terminal positions so it fits without adapters or wiring changes.
Every unit is bench tested at the factory for current draw, solenoid pull-in and pinion throw, because those three values decide whether a starter works in a cold engine bay as well as it does on a test bench.
Key Specifications
- Rated voltage: 12V
- Rated output: 4.5 kW
- Pinion: 13 teeth
- Type: reduction gear starter with pre-engaged solenoid
- Application: 6BT3.9
- Net weight: approximately 7.6 kg
- Condition: new, direct replacement for the original unit
A 12V 4.5 kW rating is the output the motor can hold while cranking, not a peak figure. It is sized so the engine reaches starting speed on the first or second revolution, which is what makes a healthy start feel immediate.
A pre-engaged solenoid pushes the pinion into mesh before the main contact closes, which prevents the tooth damage that occurs when a motor spins up against a stationary ring gear.
Reference Numbers and Cross References
The following OEM and aftermarket references are listed for this unit:
- 228000-0216
- 104452A1
- 3904466
- 6BT3.9
- 3964432
- 128000-0210
- 128000-0213
- 3675154
- 3964427
- STG92845
- 1308066H91
- 1280000212
- 1280000215
- 3957594
Cross references are a guide, not a fitment guarantee. The same engine family was often built with more than one starter, and the pinion module or terminal bracket can differ between them, so confirm the number on the unit being replaced. This starter is listed with 14 references in total.
Fitment and Application
This starter is used across 6BT3.9 variants that share the same bell housing pattern. Where the original label is missing, the pinion tooth count and terminal position are enough to identify the correct unit. On 6BT3.9 installations, access to the 104452A1 usually decides how long the job takes.
Vehicles that have had an engine or gearbox replacement may already carry a different starter from the one the catalogue expects, so treat the paperwork as a starting point rather than the final answer.
Why These Starters Fail
The brush plate is the second common failure point. Brushes shorten gradually, spring pressure falls, and contact becomes intermittent. Cranking speed drops a little every week until the engine refuses to start on a cold morning.
Most failures start at the solenoid contact. Each start switches the full cranking current through a copper disc, and after thousands of cycles that disc pits and burns. The result is the familiar single click with no rotation, or a delay before the motor turns. Owners of 6BT3.9 should treat the 104452A1 reference list as a starting point, not the final answer.
Fault Symptoms
- A single heavy click, then nothing
- Slow, laboured cranking from cold that improves once the engine runs
- Metallic scrape or whine during cranking
- Starter that disengages late, with a brief screech after the engine fires
- Burning smell near the starter after a failed start attempt
On a high-mileage vehicle, worn brushes and a burnt solenoid contact usually arrive together. If the motor bench tests well but cranking is still weak in the car, inspect the main cable and earth path before fitting another starter. Where a 104452A1 has been replaced before, check that the fitted unit still matches the reference list.
Before You Fit the Replacement
- State of charge and age of the battery
- Corrosion on the earth strap and the engine-to-body bond
- Pinion tooth count against the ring gear
- Free movement of the new pinion before fitting
- That the signal wire connector seats fully on the solenoid
Most comebacks after a starter replacement trace back to something that was not checked before the unit went on: a tired battery, a corroded earth or a chipped ring gear. Ten minutes with a multimeter and a torch prevents the second repair.
Installation Procedure
Raise and support the vehicle where the starter is reached from below, disconnect the battery, and detach the main cable and signal wire. Note the cable positions before removal so the replacement goes back the same way.
Clean the mounting face and inspect the ring gear teeth through the starter aperture. Fit the replacement with the original bolts, reconnect the cables in the same order and tighten the main terminal firmly. Crank the engine briefly and listen for clean engagement and release. The 104452A1 is built to the same flange pattern as the unit it replaces.
Quality Control and Supply from Hejian Nuojin Auto Parts Co., Ltd.
Hejian Nuojin Auto Parts Co., Ltd. manufactures starter and alternator components for the aftermarket. Every unit is bench tested for no-load current draw, solenoid pull-in and release voltage, pinion throw and running noise before packing.
Standard references are held as spot goods, volume orders are delivered in around 30 days, and every unit carries a one-year warranty against manufacturing defects.
Frequently Asked Questions
How long should a replacement starter last?
There is no fixed interval, but a starter fed by a healthy battery and a clean earth path will outlast one that is repeatedly cranked on a low battery.
Can the solenoid be replaced on its own?
Yes, when the motor tests well and only the contact has burnt. On a starter with high mileage the complete unit is usually better value, because the brushes and pinion are close behind.
How do I confirm the starter matches my vehicle?
Read the number on the starter body or on the old unit and compare it with the reference list above. Where the label is missing, match the pinion teeth and the terminal bracket against the photographs.
Should the ring gear be replaced at the same time?
Only if teeth are chipped, worn to a step or missing. Inspect the ring gear through the starter aperture before fitting the new unit.

