
Стартер 12V 3.0KW 10T 2873K404 для Perkins 1104D, 1106C, 1106D
Применимый тип:Perkins 1104D, 1106C, 1106D (page heading also lists 1006-60T и Sisu Diesel 645D; verify model, двигатель и OE number before ordering)
Номер запчасти: 2873K404, 2872K404, 63280040, 18941, 0740001000, 4280001380, 225-3148, 10000-48830, 10000-16477, 5269854, 113654, 102-260, LRS02206, LRS2206, STR52055, 3784889M2, 3784890M1, 3823621M91, T400268, T400267
| Мощность л.с. : | 12V 3.0KW |
| Число футов : | 10T |
| Размер : | 24*12*16single unit inner box |
| Вес : | Вес нетто 6 кг |
| Упаковочные материалы : | Нейтральная упаковка из крафт-бумаги |
| Спотовые / предварительные продажи : | В наличии |
| Гарантия : | 1 год |
| Номер продукта : |
| Тип : | стартер |
| Спецификация : | 12V 3.0KW |
| Число футов : | 10T |
| Марка : | nuojin |
| Цифры : | 2873K404 |
| Качество : | НОВЫЙ |
| Время поставки : | 10 дней |





Overview of the 2873K404 Starter Motor
The 2873K404 starter motor is a 12V, 3.0 kW unit built for Perkins 1104D, 1106C, 1106D. It is a reduction-gear starter with a pre-engaged solenoid, assembled to the original mounting flange and terminal positions so it fits without adapters or wiring changes.
Every unit is bench tested at the factory for current draw, solenoid pull-in and pinion throw, because those three values decide whether a starter works in a cold engine bay as well as it does on a test bench.
Specification Summary
- Rated voltage: 12V
- Rated output: 3.0 kW
- Pinion: 10 teeth
- Type: reduction gear starter with pre-engaged solenoid
- Application: Perkins 1104D, 1106C, 1106D
- Net weight: approximately 6 kg
- Condition: new, direct replacement for the original unit
A 12V 3.0 kW rating is the output the motor can hold while cranking, not a peak figure. It is sized so the engine reaches starting speed on the first or second revolution, which is what makes a healthy start feel immediate.
The reduction gearset lets the motor run at high speed while the pinion turns slowly with high torque, which is why the unit stays compact enough for a crowded engine bay.
Reference Numbers and Cross References
The starter is supplied against the following references, which help identify it against the unit already fitted to the vehicle:
- 2873K404
- 1104D
- 1106C
- 2872K404
- 63280040
- 0740001000
- 4280001380
- 3784889M2
- LRS02206
- 225-3148
- 10000-48830
- 10000-16477
- 5269854
- 113654
- 102-260
- LRS2206
Where the label on the old starter has corroded, compare the pinion teeth, the mounting flange and the terminal bracket with the photographs before ordering. The number on the original unit is the reliable identifier. This starter is listed with 16 references in total.
Application Notes
Perkins 1104D, 1106C, 1106D applications in this range share the same mounting pattern and terminal layout, which is why one reference can serve several model years. Fitment is still decided by the starter number rather than by the badge on the vehicle. For the 2873K404, the practical check is the number stamped on the housing.
A mismatched pinion is the most common cause of a starter that engages noisily or refuses to mesh. Compare the tooth count before fitting, not after.
Common Failure Patterns
Most failures start at the solenoid contact. Each start switches the full cranking current through a copper disc, and after thousands of cycles that disc pits and burns. The result is the familiar single click with no rotation, or a delay before the motor turns.
The brush plate is the second common failure point. Brushes shorten gradually, spring pressure falls, and contact becomes intermittent. Cranking speed drops a little every week until the engine refuses to start on a cold morning. For the 2873K404, the practical check is the number stamped on the housing.
Symptoms of a Failing Starter
- No-crank with a fully charged battery
- Cranking that slows noticeably as the engine bay heats up
- Grinding that disappears on a second attempt
- Whine under load, suggesting a slipping pinion clutch
- Starter that continues to spin for a second after the engine fires
Rule out the simple causes first: battery capacity under load, corroded terminals and the signal wire at the solenoid. A starter that clicks with a known-good battery and a clean signal circuit has an internal contact fault. On Perkins 1104D, 1106C, 1106D installations, access to the 2873K404 usually decides how long the job takes.
What to Check Before Fitting
- Condition of the old pinion and ring gear before the new unit goes in
- Main cable continuity and the condition of the lug at the starter stud
- Battery voltage while cranking, measured at the battery posts
- Mounting face cleanliness and bolt condition
- That the replacement terminal layout matches the original harness
Fitting a new starter onto a worn ring gear or a marginal battery shortens its life. Check the simple items first, then fit the unit once and correctly.
Installation Procedure
With the battery isolated, remove any heat shield or ducting that blocks access and disconnect the main cable and solenoid connector. Support the unit before the mounting bolts come out; these starters are heavy enough to damage surrounding parts if they drop.
Check the ring gear through the aperture before fitting. Install the new unit with the original bolts, reconnect the cables in the same order and tighten the main terminal without over-stressing the stud. Crank briefly and confirm the pinion releases as the engine fires. The 2873K404 is built to the same flange pattern as the unit it replaces.
Quality Control and Supply from Hejian Nuojin Auto Parts Co., Ltd.
Hejian Nuojin Auto Parts Co., Ltd. manufactures starter and alternator components for the aftermarket. Every unit is bench tested for no-load current draw, solenoid pull-in and release voltage, pinion throw and running noise before packing.
Standard references are held as spot goods, volume orders are delivered in around 30 days, and every unit carries a one-year warranty against manufacturing defects.
Frequently Asked Questions
How do I confirm the starter matches my vehicle?
Read the number on the starter body or on the old unit and compare it with the reference list above. Where the label is missing, match the pinion teeth and the terminal bracket against the photographs.
Can I test the starter on the bench?
Yes. Apply battery voltage to the main stud and the signal terminal and check that the pinion throws and the motor turns. A clamp meter reading against the rated current will show whether the unit is drawing too much.
Does the starter need any maintenance?
No routine maintenance is required. Keeping the battery, terminals and earth connections clean is what extends starter life in practice.
Can the solenoid be replaced on its own?
It is possible, provided the motor draws normal current and the pinion is sound. Where the brushes are already short, replacing the complete starter avoids a second repair within a year.

