
Стартер 12V 3.0KW 10T 2873K405 для Perkins двигатели и Perkins-powered FARMTRAC, Massey
Применимый тип:Perkins двигатели и Perkins-powered FARMTRAC, Massey Ferguson и McCormick tractors (1004-40, 1004-4T, 1004-42, 1006.6T, 1103D, 1104D-44T, 1104D-44TA, 1104, 6-cylinder platforms; verify двигатель и OE number before ordering)
Номер запчасти:2873K405, 2872K405, 2873K634, 428000-1290, 71440231, 71440531, 18940, 220702, 11131781, 254193, 254193M, 6030170, 63280041, 860715, 26.0005, 26.0005M, 0740000000, 2253149, AZE4173, 8719R, AEX1050, CGB-93405, CST30170AS, DRS3954, DRS3954N, EAA-121063, MAV321700, RNL2873K405, S4030, MSN8041, IS1201, STR52056, LRS02425, LRS2425, STR9009, 2873K624, 2873K625
| Мощность л.с. : | 12V 3.0KW |
| Число футов : | 10T |
| Размер : | 24*12*16single unit inner box |
| Вес : | Вес нетто 5,9 кг, вес брутто 6,2 г |
| Упаковочные материалы : | Нейтральная упаковка из крафт-бумаги |
| Спотовые / предварительные продажи : | В наличии |
| Гарантия : | 1 год |
| Номер продукта : |
| Тип : | генератор |
| Спецификация : | 12V 3.0KW |
| Число футов : | 10T |
| Марка : | nuojin |
| Цифры : | 2873K405 |
| Качество : | НОВЫЙ |
| Время поставки : | 10 дней |





Overview of the 2873K405 Starter Motor
Perkins engines and Perkins-powered FARMTRAC, Massey owners replacing a tired starter will find the 2873K405 a direct fit: a 12V, 3.0 kW reduction-gear unit with a pre-engaged solenoid, produced to the original flange and terminal layout.
The starter carries the full cranking current through its brushes and solenoid contact, so every start costs a little material. That is why the unit is normally replaced once, at the end of a long service life, rather than repaired repeatedly.
Technical Summary
- Rated voltage: 12V
- Rated output: 3.0 kW
- Pinion: 10 teeth
- Type: reduction gear starter with pre-engaged solenoid
- Application: Perkins engines and Perkins-powered FARMTRAC, Massey
- Condition: new, direct replacement for the original unit
A 12V 3.0 kW rating is the output the motor can hold while cranking, not a peak figure. It is sized so the engine reaches starting speed on the first or second revolution, which is what makes a healthy start feel immediate.
The drive end housing is cast aluminium and carries the pinion bearing, so the pinion stays square to the ring gear when the motor delivers full torque.
Reference Numbers and Cross References
The reference family for this starter covers the numbers listed here:
- 2873K405
- 2872K405
- 2873K634
- 428000-1290
- 71440531
- 63280041
- 71440231
- 11131781
- 254193
- 254193M
- 6030170
- 860715
- 26.0005
- 26.0005M
- 0740000000
- 2253149
Where the label on the old starter has corroded, compare the pinion teeth, the mounting flange and the terminal bracket with the photographs before ordering. The number on the original unit is the reliable identifier. This starter is listed with 16 references in total.
Matching the Unit to the Vehicle
The unit is listed for Perkins engines and Perkins-powered FARMTRAC, Massey. Because manufacturers changed starter suppliers during the production run, the safest check is the number stamped on the starter body, not the model year alone. Owners of Perkins engines and Perkins-powered FARMTRAC, Massey should treat the 2873K405 reference list as a starting point, not the final answer.
A mismatched pinion is the most common cause of a starter that engages noisily or refuses to mesh. Compare the tooth count before fitting, not after.
What Wears Out First
Oil or coolant mist from a leaking seal finds its way into the drive end housing, mixes with carbon dust and forms a conductive paste. The starter then arcs internally and fails early, whatever its mileage.
Most failures start at the solenoid contact. Each start switches the full cranking current through a copper disc, and after thousands of cycles that disc pits and burns. The result is the familiar single click with no rotation, or a delay before the motor turns. This applies in particular to the 2873K405 supplied for Perkins engines and Perkins-powered FARMTRAC, Massey.
What to Look For
- No-crank with a fully charged battery
- Cranking that slows noticeably as the engine bay heats up
- Grinding that disappears on a second attempt
- Whine under load, suggesting a slipping pinion clutch
- Starter that continues to spin for a second after the engine fires
Before replacing the starter, check the battery state of charge, the terminal clamps, the engine earth strap and the main cable. On vehicles of this age a corroded earth connection produces exactly the same slow-crank symptom and costs far less to correct. Owners of Perkins engines and Perkins-powered FARMTRAC, Massey should treat the 2873K405 reference list as a starting point, not the final answer.
What to Check Before Fitting
- State of charge and age of the battery
- Corrosion on the earth strap and the engine-to-body bond
- Pinion tooth count against the ring gear
- Free movement of the new pinion before fitting
- That the signal wire connector seats fully on the solenoid
Most comebacks after a starter replacement trace back to something that was not checked before the unit went on: a tired battery, a corroded earth or a chipped ring gear. Ten minutes with a multimeter and a torch prevents the second repair.
Fitting the Replacement
Disconnect the battery negative terminal, remove the intake parts that restrict access, then disconnect the main cable and the solenoid signal connector. Support the starter before removing the mounting bolts.
Clean the mounting face and inspect the ring gear teeth through the starter aperture. Fit the replacement with the original bolts, reconnect the cables in the same order and tighten the main terminal firmly. Crank the engine briefly and listen for clean engagement and release. Owners of Perkins engines and Perkins-powered FARMTRAC, Massey should treat the 2873K405 reference list as a starting point, not the final answer.
Quality Control and Supply from Hejian Nuojin Auto Parts Co., Ltd.
Hejian Nuojin Auto Parts Co., Ltd. manufactures starter and alternator components for the aftermarket. Every unit is bench tested for no-load current draw, solenoid pull-in and release voltage, pinion throw and running noise before packing.
Standard references are held as spot goods, volume orders are delivered in around 30 days, and every unit carries a one-year warranty against manufacturing defects.
Frequently Asked Questions
Does this starter come with the solenoid?
Yes. The unit is supplied complete with its solenoid, as shown in the product photographs. Mounting bolts are not included.
Does the starter need any maintenance?
No routine maintenance is required. Keeping the battery, terminals and earth connections clean is what extends starter life in practice.
Can the solenoid be replaced on its own?
Yes, when the motor tests well and only the contact has burnt. On a starter with high mileage the complete unit is usually better value, because the brushes and pinion are close behind.
How long should a replacement starter last?
Service life depends on starting frequency, battery condition and heat exposure. On a daily-driven vehicle with clean connections, ten years or more is realistic.

