
Стартер 12V 1.4KW 9T 2-3137-DR для Buick Chevrolet GMC Saturn
Применимый тип:Fits Buick Chevrolet GMC Saturn
Номер запчасти:8000213, 89060407, 12609317, 12-60-9317 323-1657 LRS03880 6947N 115773,8000213,8200213,DRS0942,1202186 J5210914,063721543010,MQS1543 300N10693Z 6947 2-3137-DR 8000213 12609317,48410489,5556245
| Мощность л.с. : | 12V 1.4KW |
| Число футов : | 9T |
| Размер : | 24*18*17single unit inner box |
| Вес : | Вес нетто 2,8 кг, вес брутто 2,95 кг |
| Упаковочные материалы : | Нейтральная упаковка из крафт-бумаги |
| Спотовые / предварительные продажи : | В наличии |
| Гарантия : | 1 год |
| Номер продукта : |
| Тип : | стартер |
| Спецификация : | 12V 1.4KW |
| Число футов : | 9T |
| Марка : | nuojin |
| Цифры : | 6947 2-3137-DR 12609317 |
| Качество : | НОВЫЙ |
| Время поставки : | 10 дней |






Overview of the 2-3137-DR Starter Motor
The 2-3137-DR starter motor is a 12V, 1.4 kW unit built for Fits Buick Chevrolet GMC Saturn. It is a reduction-gear starter with a pre-engaged solenoid, assembled to the original mounting flange and terminal positions so it fits without adapters or wiring changes.
Cranking load varies with temperature, battery condition and engine condition. A healthy starter has margin for all three; a worn one turns the engine just slowly enough that the control unit hesitates and the driver notices long, laboured starts.
Specification Summary
- Rated voltage: 12V
- Rated output: 1.4 kW
- Pinion: 9 teeth
- Type: reduction gear starter with pre-engaged solenoid
- Application: Fits Buick Chevrolet GMC Saturn
- Net weight: approximately 2.95 kg
- Condition: new, direct replacement for the original unit
A 12V 1.4 kW rating is the output the motor can hold while cranking, not a peak figure. It is sized so the engine reaches starting speed on the first or second revolution, which is what makes a healthy start feel immediate.
A pre-engaged solenoid pushes the pinion into mesh before the main contact closes, which prevents the tooth damage that occurs when a motor spins up against a stationary ring gear.
Reference Numbers and Cross References
The reference family for this starter covers the numbers listed here:
- 2-3137-DR
- 8000213
- 12609317
- 48410489
- 5556245
- 89060407
- 12-60-9317
- 323-1657
- LRS03880
- 6947N
- 115773
- DRS0942
- J5210914
- 063721543010
- MQS1543
- 300N10693Z
Several numbers in this list belong to complete starter assemblies while others refer to the motor only. A visual check of the drive end protects against the most common ordering error. This starter is listed with 16 references in total.
Application Notes
Fits Buick Chevrolet GMC Saturn applications in this range share the same mounting pattern and terminal layout, which is why one reference can serve several model years. Fitment is still decided by the starter number rather than by the badge on the vehicle. For the 2-3137-DR, the practical check is the number stamped on the housing.
Vehicles that have had an engine or gearbox replacement may already carry a different starter from the one the catalogue expects, so treat the paperwork as a starting point rather than the final answer.
Failure Causes
Heat is the underlying cause in most cases. The starter sits close to the exhaust, and after a hot shutdown the solenoid winding and brush plate soak in heat with no airflow. Resin hardens, springs lose tension and the contact oxidises.
Most failures start at the solenoid contact. Each start switches the full cranking current through a copper disc, and after thousands of cycles that disc pits and burns. The result is the familiar single click with no rotation, or a delay before the motor turns. The 2-3137-DR ships with its solenoid fitted, so no parts have to be transferred from the old unit.
Fault Symptoms
- A single heavy click, then nothing
- Slow, laboured cranking from cold that improves once the engine runs
- Metallic scrape or whine during cranking
- Starter that disengages late, with a brief screech after the engine fires
- Burning smell near the starter after a failed start attempt
Rule out the simple causes first: battery capacity under load, corroded terminals and the signal wire at the solenoid. A starter that clicks with a known-good battery and a clean signal circuit has an internal contact fault. The 2-3137-DR ships with its solenoid fitted, so no parts have to be transferred from the old unit.
What to Check Before Fitting
- Battery capacity under load, not just open-circuit voltage
- Terminal clamps and the main cable lug for corrosion or heat marks
- Earth strap between engine and chassis
- Ring gear teeth, visible through the starter aperture
- Key switch and signal wire voltage at the solenoid terminal
Most comebacks after a starter replacement trace back to something that was not checked before the unit went on: a tired battery, a corroded earth or a chipped ring gear. Ten minutes with a multimeter and a torch prevents the second repair.
Fitting the Replacement
With the battery isolated, remove any heat shield or ducting that blocks access and disconnect the main cable and solenoid connector. Support the unit before the mounting bolts come out; these starters are heavy enough to damage surrounding parts if they drop.
Check the ring gear through the aperture before fitting. Install the new unit with the original bolts, reconnect the cables in the same order and tighten the main terminal without over-stressing the stud. Crank briefly and confirm the pinion releases as the engine fires. Fitting the 2-3137-DR correctly takes less time than diagnosing the original fault.
Quality Control and Supply from Hejian Nuojin Auto Parts Co., Ltd.
Each production batch is inspected for housing dimensions, terminal integrity and pinion fit, and every starter is bench tested before it is boxed. Units ship in neutral cartons with foam protection, which keeps freight damage low and allows distributors to label stock under their own brand.
Standard references are held as spot goods, volume orders are delivered in around 30 days, and every unit carries a one-year warranty against manufacturing defects.
Frequently Asked Questions
Can I test the starter on the bench?
Yes. Apply battery voltage to the main stud and the signal terminal and check that the pinion throws and the motor turns. A clamp meter reading against the rated current will show whether the unit is drawing too much.
Why does the starter work cold but fail when hot?
Heat raises solenoid resistance and reduces brush spring pressure. Both effects build up gradually and appear first on a hot restart.
Can the solenoid be replaced on its own?
Yes, when the motor tests well and only the contact has burnt. On a starter with high mileage the complete unit is usually better value, because the brushes and pinion are close behind.
Does the starter need any maintenance?
No routine maintenance is required. Keeping the battery, terminals and earth connections clean is what extends starter life in practice.

