
Стартер 12V 3E7905 для Caterpillar backhoe loaders 416B, 426B, 428B и 436B, plus
Применимый тип:Caterpillar backhoe loaders 416B, 426B, 428B и 436B, plus 414E, 416C, 416D, 420D и 420E models (verify model, двигатель, voltage и OE number before ordering)
Номер запчасти:143-0538, 143-0539, 3E7905, 228000-1350, 6V-0492, 0R-4316, 9742809-166, 428000-1660, 428000-1661, 2873K409, 32A600-02101, 32A66-02100, DSN2115
| Мощность л.с. : | 12V 2.5KW |
| Число футов : | 10T |
| Размер : | 44*24*19 cm single unit inner box |
| Вес : | Вес нетто 7,85 кг, вес брутто 8,4 кг |
| Упаковочные материалы : | Нейтральная упаковка из крафт-бумаги |
| Спотовые / предварительные продажи : | В наличии |
| Гарантия : | 1 год |
| Номер продукта : |
| Тип : | стартер |
| Спецификация : | 12V 2.5KW |
| Число футов : | 10t |
| Марка : | NUOJIN |
| Цифры : | 143-0538 |
| Качество : | НОВЫЙ |
| Время поставки : | 10 дней |





Overview of the 3E7905 Starter Motor
This 3E7905 starter motor is the 12V, 2.5 kW replacement for Caterpillar backhoe loaders 416B, 426B, 428B and 436B, plus applications. The housing, drive end and terminal positions follow the original design, so the unit bolts straight onto the bell housing and reuses the existing cabling.
Every unit is bench tested at the factory for current draw, solenoid pull-in and pinion throw, because those three values decide whether a starter works in a cold engine bay as well as it does on a test bench.
Specifications at a Glance
- Rated voltage: 12V
- Rated output: 2.5 kW
- Pinion: 10 teeth
- Type: reduction gear starter with pre-engaged solenoid
- Application: Caterpillar backhoe loaders 416B, 426B, 428B and 436B, plus
- Net weight: approximately 8.4 kg
- Condition: new, direct replacement for the original unit
A 12V 2.5 kW rating is the output the motor can hold while cranking, not a peak figure. It is sized so the engine reaches starting speed on the first or second revolution, which is what makes a healthy start feel immediate.
The drive end housing is cast aluminium and carries the pinion bearing, so the pinion stays square to the ring gear when the motor delivers full torque.
Reference Numbers and Cross References
The starter is supplied against the following references, which help identify it against the unit already fitted to the vehicle:
- 143-0538
- 416B
- 426B
- 428B
- 143-0539
- 3E7905
- 6V-0492
- 0R-4316
- 228000-1350
- 428000-1660
- 9742809-166
- 428000-1661
- 2873K409
- 32A600-02101
- 32A66-02100
- DSN2115
Starter suppliers revised this design more than once during production. Confirm the number on the old unit, or send a photograph of the drive end, before committing to an order. This starter is listed with 16 references in total.
Where This Starter Is Used
Caterpillar backhoe loaders 416B, 426B, 428B and 436B, plus applications in this range share the same mounting pattern and terminal layout, which is why one reference can serve several model years. Fitment is still decided by the starter number rather than by the badge on the vehicle. On Caterpillar backhoe loaders 416B, 426B, 428B and 436B, plus installations, access to the 3E7905 usually decides how long the job takes.
When ordering for a fleet, quote the starter number from each vehicle rather than a single model reference; mixed build dates are common and the starter changed with them.
Common Failure Patterns
Most failures start at the solenoid contact. Each start switches the full cranking current through a copper disc, and after thousands of cycles that disc pits and burns. The result is the familiar single click with no rotation, or a delay before the motor turns.
The brush plate is the second common failure point. Brushes shorten gradually, spring pressure falls, and contact becomes intermittent. Cranking speed drops a little every week until the engine refuses to start on a cold morning. Where a 3E7905 has been replaced before, check that the fitted unit still matches the reference list.
Symptoms of a Failing Starter
- No-crank with a fully charged battery
- Cranking that slows noticeably as the engine bay heats up
- Grinding that disappears on a second attempt
- Whine under load, suggesting a slipping pinion clutch
- Starter that continues to spin for a second after the engine fires
Before replacing the starter, check the battery state of charge, the terminal clamps, the engine earth strap and the main cable. On vehicles of this age a corroded earth connection produces exactly the same slow-crank symptom and costs far less to correct. The 3E7905 is built to the same flange pattern as the unit it replaces.
Pre-Fit Checklist
- Condition of the old pinion and ring gear before the new unit goes in
- Main cable continuity and the condition of the lug at the starter stud
- Battery voltage while cranking, measured at the battery posts
- Mounting face cleanliness and bolt condition
- That the replacement terminal layout matches the original harness
Fitting a new starter onto a worn ring gear or a marginal battery shortens its life. Check the simple items first, then fit the unit once and correctly.
Fitting the Replacement
Raise and support the vehicle where the starter is reached from below, disconnect the battery, and detach the main cable and signal wire. Note the cable positions before removal so the replacement goes back the same way.
Clean the mounting face and inspect the ring gear teeth through the starter aperture. Fit the replacement with the original bolts, reconnect the cables in the same order and tighten the main terminal firmly. Crank the engine briefly and listen for clean engagement and release. The 3E7905 ships with its solenoid fitted, so no parts have to be transferred from the old unit.
Quality Control and Supply from Hejian Nuojin Auto Parts Co., Ltd.
Hejian Nuojin Auto Parts Co., Ltd. manufactures starter and alternator components for the aftermarket. Every unit is bench tested for no-load current draw, solenoid pull-in and release voltage, pinion throw and running noise before packing.
Common references are kept in stock for fast dispatch, volume orders are delivered in around 30 days and each starter carries a one-year warranty against manufacturing defects.
Frequently Asked Questions
Can I test the starter on the bench?
Yes. Apply battery voltage to the main stud and the signal terminal and check that the pinion throws and the motor turns. A clamp meter reading against the rated current will show whether the unit is drawing too much.
Is a 12V and a 24V starter interchangeable?
No. The voltage rating must match the vehicle system; fitting the wrong unit will damage the starter and the wiring.
Does this starter come with the solenoid?
The starter is supplied as a complete assembly including the solenoid. Reuse the original mounting bolts if they are in good condition.
Why does the starter click but not turn?
A click with no rotation usually means the solenoid pulls in but the contact does not pass current. Check the earth strap and the main cable before condemning the starter.

