
Стартер 12V 1.4KW 11T CST60102 для Mercruiser I, O 4.3, 5.0, 5.7 и 8.1 .
Применимый тип:Mercruiser I/O 4.3, 5.0, 5.7 и 8.1 (Carb и EFI).
Номер запчасти:3857747, F042003047, 112239, 115985, CST60102, CST60102AS, CST601002ES, 8000108, 8000282, 9000839, 9000840, 9000850, 9000851, 9000884, STD2239AB, STD2239BA, 50-807907, 50807904A1, 50808011A1, 863007A1, 21999DR2, 6792N.
| Мощность л.с. : | 12v 1.4KW |
| Число футов : | 9T11T |
| Размер : | 24*18*17single unit inner box |
| Вес : | Вес нетто 3,45 кг, вес брутто 3,6 кг |
| Упаковочные материалы : | Нейтральная упаковка из крафт-бумаги |
| Спотовые / предварительные продажи : | В наличии |
| Гарантия : | 1 год |
| Номер продукта : |
| Тип : | стартер |
| Спецификация : | 12v 1.4KW |
| Число футов : | 9T11T |
| Марка : | nuojin |
| Цифры : | 3857747 9000839 |
| Качество : | НОВЫЙ |
| Время поставки : | 10 дней |





Overview of the CST60102 Starter Motor
This CST60102 starter motor is the 12V, 1.4 kW replacement for Mercruiser I, O 4.3, 5.0, 5.7 and 8.1 . applications. The housing, drive end and terminal positions follow the original design, so the unit bolts straight onto the bell housing and reuses the existing cabling.
Cranking load varies with temperature, battery condition and engine condition. A healthy starter has margin for all three; a worn one turns the engine just slowly enough that the control unit hesitates and the driver notices long, laboured starts.
Key Specifications
- Rated voltage: 12V
- Rated output: 1.4 kW
- Pinion: 11 teeth
- Type: reduction gear starter with pre-engaged solenoid
- Application: Mercruiser I, O 4.3, 5.0, 5.7 and 8.1 .
- Net weight: approximately 3.6 kg
- Condition: new, direct replacement for the original unit
A 12V 1.4 kW rating is the output the motor can hold while cranking, not a peak figure. It is sized so the engine reaches starting speed on the first or second revolution, which is what makes a healthy start feel immediate.
The reduction gearset lets the motor run at high speed while the pinion turns slowly with high torque, which is why the unit stays compact enough for a crowded engine bay.
Reference Numbers and Cross References
Cross references for this starter are listed below. They are a matching aid rather than a substitute for checking the number on the old unit:
- 3857747
- CST60102
- J1171
- 112239
- 115985
- CST60102AS
- CST601002ES
- 8000108
- 8000282
- 9000839
- 9000840
- 9000850
- 9000851
- 9000884
- STD2239AB
- STD2239BA
Starter suppliers revised this design more than once during production. Confirm the number on the old unit, or send a photograph of the drive end, before committing to an order. This starter is listed with 16 references in total.
Fitment and Application
This starter family was fitted to a range of Mercruiser applications, and the part number changed as engines and flywheels were revised. The unit listed here covers the references above and is a direct replacement where those numbers match. The CST60102 ships with its solenoid fitted, so no parts have to be transferred from the old unit.
When ordering for a fleet, quote the starter number from each vehicle rather than a single model reference; mixed build dates are common and the starter changed with them.
What Wears Out First
Oil or coolant mist from a leaking seal finds its way into the drive end housing, mixes with carbon dust and forms a conductive paste. The starter then arcs internally and fails early, whatever its mileage.
Heat is the underlying cause in most cases. The starter sits close to the exhaust, and after a hot shutdown the solenoid winding and brush plate soak in heat with no airflow. Resin hardens, springs lose tension and the contact oxidises. Because the CST60102 reuses the original bolts and connectors, no adapters are needed on Mercruiser I, O 4.3, 5.0, 5.7 and 8.1 ..
What to Look For
- No-crank with a fully charged battery
- Cranking that slows noticeably as the engine bay heats up
- Grinding that disappears on a second attempt
- Whine under load, suggesting a slipping pinion clutch
- Starter that continues to spin for a second after the engine fires
Rule out the simple causes first: battery capacity under load, corroded terminals and the signal wire at the solenoid. A starter that clicks with a known-good battery and a clean signal circuit has an internal contact fault. Because the CST60102 reuses the original bolts and connectors, no adapters are needed on Mercruiser I, O 4.3, 5.0, 5.7 and 8.1 ..
Checks Before Installation
- Condition of the old pinion and ring gear before the new unit goes in
- Main cable continuity and the condition of the lug at the starter stud
- Battery voltage while cranking, measured at the battery posts
- Mounting face cleanliness and bolt condition
- That the replacement terminal layout matches the original harness
Fitting a new starter onto a worn ring gear or a marginal battery shortens its life. Check the simple items first, then fit the unit once and correctly.
Fitting the Replacement
Disconnect the battery negative terminal, remove the intake parts that restrict access, then disconnect the main cable and the solenoid signal connector. Support the starter before removing the mounting bolts.
Clean the mounting face and inspect the ring gear teeth through the starter aperture. Fit the replacement with the original bolts, reconnect the cables in the same order and tighten the main terminal firmly. Crank the engine briefly and listen for clean engagement and release. For the CST60102, the practical check is the number stamped on the housing.
Quality Control and Supply from Hejian Nuojin Auto Parts Co., Ltd.
Each production batch is inspected for housing dimensions, terminal integrity and pinion fit, and every starter is bench tested before it is boxed. Units ship in neutral cartons with foam protection, which keeps freight damage low and allows distributors to label stock under their own brand.
Standard references are held as spot goods, volume orders are delivered in around 30 days, and every unit carries a one-year warranty against manufacturing defects.
Frequently Asked Questions
How long should a replacement starter last?
Service life depends on starting frequency, battery condition and heat exposure. On a daily-driven vehicle with clean connections, ten years or more is realistic.
Why does the starter click but not turn?
A click with no rotation usually means the solenoid pulls in but the contact does not pass current. Check the earth strap and the main cable before condemning the starter.
Should the ring gear be replaced at the same time?
Only if teeth are chipped, worn to a step or missing. Inspect the ring gear through the starter aperture before fitting the new unit.
How do I confirm the starter matches my vehicle?
Compare the original part number first, then check the pinion tooth count and the terminal connector layout. The vehicle model alone is not enough, because more than one starter was fitted during production.

