
Стартер 12V 1.4KW 9T E301.5 для Caterpillar C1.1 E301.5
Применимый тип:Caterpillar C1.1 E301.5
Номер запчасти:0001107078 00001108181 986022480 3197351 3408308 063521070780 063521070780、MSN2016、0001108181、0986022480、3197351 3408308、18508662、185086620 21302969、3582514、3801351 3803584、8000278、185086321 18508661、185086610 MSN2016,0001107078、 0986022480
| Мощность л.с. : | 12V 1.4KW |
| Число футов : | 9T |
| Размер : | |
| Вес : | Вес нетто 2,9 кг |
| Упаковочные материалы : | Neutral packaging |
| Спотовые / предварительные продажи : | Presale |
| Гарантия : | 1 год |
| Номер продукта : |
| Тип : | стартер |
| Спецификация : | 12V 1.4KW |
| Число футов : | 9T |
| Марка : | NUOJIN |
| Цифры : | 0001107078 00001108181 |
| Качество : | НОВЫЙ |
| Время поставки : | 30 дней |






Overview of the E301.5 Starter Motor
The E301.5 is a 12V, 1.4 kW starter motor supplied for Caterpillar C1.1 E301.5. A reduction gearset between motor and pinion keeps the body compact while still delivering the cranking torque the engine needs.
Because the motor is only used in short bursts, heat builds up quickly and escapes slowly. A starter that has worked for years in traffic or on site will show heat-hardened resin, shortened brushes and a pitted solenoid contact long before the windings fail.
Technical Summary
- Rated voltage: 12V
- Rated output: 1.4 kW
- Pinion: 9 teeth
- Type: reduction gear starter with pre-engaged solenoid
- Application: Caterpillar C1.1 E301.5
- Net weight: approximately 2.9 kg
- Condition: new, direct replacement for the original unit
A 12V 1.4 kW rating is the output the motor can hold while cranking, not a peak figure. It is sized so the engine reaches starting speed on the first or second revolution, which is what makes a healthy start feel immediate.
The reduction gearset lets the motor run at high speed while the pinion turns slowly with high torque, which is why the unit stays compact enough for a crowded engine bay.
Reference Numbers and Cross References
The reference family for this starter covers the numbers listed here:
- 0001107078
- 00001108181
- 986022480
- 3408308
- 063521070780
- 0001108181
- 0986022480
- C1.1
- E301.5
- 18508662
- 185086620
- 21302969
- 3582514
- 3801351
- 3803584
- 8000278
Starter suppliers revised this design more than once during production. Confirm the number on the old unit, or send a photograph of the drive end, before committing to an order. This starter is listed with 16 references in total.
Application Notes
This starter is used across Caterpillar C1.1 E301.5 variants that share the same bell housing pattern. Where the original label is missing, the pinion tooth count and terminal position are enough to identify the correct unit. This applies in particular to the E301.5 supplied for Caterpillar C1.1 E301.5.
When ordering for a fleet, quote the starter number from each vehicle rather than a single model reference; mixed build dates are common and the starter changed with them.
Why These Starters Fail
The brush plate is the second common failure point. Brushes shorten gradually, spring pressure falls, and contact becomes intermittent. Cranking speed drops a little every week until the engine refuses to start on a cold morning.
Most failures start at the solenoid contact. Each start switches the full cranking current through a copper disc, and after thousands of cycles that disc pits and burns. The result is the familiar single click with no rotation, or a delay before the motor turns. This applies in particular to the E301.5 supplied for Caterpillar C1.1 E301.5.
Fault Symptoms
- No-crank with a fully charged battery
- Cranking that slows noticeably as the engine bay heats up
- Grinding that disappears on a second attempt
- Whine under load, suggesting a slipping pinion clutch
- Starter that continues to spin for a second after the engine fires
A cranking voltage test separates the starter from the rest of the circuit. If battery voltage stays healthy at the terminals but drops sharply at the starter stud, the cable or the connection is at fault rather than the motor. For the E301.5, the practical check is the number stamped on the housing.
What to Check Before Fitting
- Condition of the old pinion and ring gear before the new unit goes in
- Main cable continuity and the condition of the lug at the starter stud
- Battery voltage while cranking, measured at the battery posts
- Mounting face cleanliness and bolt condition
- That the replacement terminal layout matches the original harness
Most comebacks after a starter replacement trace back to something that was not checked before the unit went on: a tired battery, a corroded earth or a chipped ring gear. Ten minutes with a multimeter and a torch prevents the second repair.
Fitting Guidance
Raise and support the vehicle where the starter is reached from below, disconnect the battery, and detach the main cable and signal wire. Note the cable positions before removal so the replacement goes back the same way.
Inspect the ring gear teeth and the mounting face, then fit the replacement and torque the bolts evenly. Reconnect the main cable and signal wire, crank the engine for a moment and listen for clean engagement without a screech or grind. This applies in particular to the E301.5 supplied for Caterpillar C1.1 E301.5.
Quality Control and Supply from Hejian Nuojin Auto Parts Co., Ltd.
Each production batch is inspected for housing dimensions, terminal integrity and pinion fit, and every starter is bench tested before it is boxed. Units ship in neutral cartons with foam protection, which keeps freight damage low and allows distributors to label stock under their own brand.
Common references are kept in stock for fast dispatch, volume orders are delivered in around 30 days and each starter carries a one-year warranty against manufacturing defects.
Frequently Asked Questions
How do I confirm the starter matches my vehicle?
Compare the original part number first, then check the pinion tooth count and the terminal connector layout. The vehicle model alone is not enough, because more than one starter was fitted during production.
Can I test the starter on the bench?
Yes. Apply battery voltage to the main stud and the signal terminal and check that the pinion throws and the motor turns. A clamp meter reading against the rated current will show whether the unit is drawing too much.
How long should a replacement starter last?
There is no fixed interval, but a starter fed by a healthy battery and a clean earth path will outlast one that is repeatedly cranked on a low battery.
Should the ring gear be replaced at the same time?
Inspect it, but replace it only when the teeth show damage. A worn ring gear will damage a new pinion within a few starts.

