
Стартер 12V 0.8KW 10T E7194-63010 для JOHN DEERE Lawn LX173,STX30,STX38 1989-1996
Применимый тип:JOHN DEERE Lawn LX173,STX30,STX38 1989–1996
Номер запчасти: 6744 2409801 2509809 2509808 2509811 E7194-63010, E7194-63012, 10455513, 10455516, 8000335 KH-25-098-09-S 2509821 25-098-08, 25-098-21-S, 25-098-08-S, 25-098-24-S, E719463010, E719463012 25-098-20, 25-098-09-S, 25-098-14, 25-098-11-S AM132702,MIA11473,AUC15258,MIA13172 25-098-14-S, 25-098-20-S,2509808,2509811, 25-098-11- 25-098-09
| Мощность л.с. : | 12V 0.8KW |
| Число футов : | 10T |
| Размер : | 24*12*16single unit inner box |
| Вес : | Вес нетто 3,5 кг, вес брутто 3,65 кг |
| Упаковочные материалы : | Нейтральная упаковка из крафт-бумаги |
| Спотовые / предварительные продажи : | В наличии |
| Гарантия : | 1 год |
| Номер продукта : |
| Тип : | стартер |
| Спецификация : | 12V 0.8KW |
| Число футов : | 10T |
| Марка : | NUOJIN |
| Цифры : | 6744 2509809 |
| Качество : | НОВЫЙ |
| Время поставки : | 7--10DAY |





Overview of the E7194-63010 Starter Motor
This E7194-63010 starter motor is the 12V, 0.8 kW replacement for JOHN DEERE Lawn LX173,STX30,STX38 1989-1996 applications. The housing, drive end and terminal positions follow the original design, so the unit bolts straight onto the bell housing and reuses the existing cabling.
Because the motor is only used in short bursts, heat builds up quickly and escapes slowly. A starter that has worked for years in traffic or on site will show heat-hardened resin, shortened brushes and a pitted solenoid contact long before the windings fail.
Technical Summary
- Rated voltage: 12V
- Rated output: 0.8 kW
- Pinion: 10 teeth
- Type: reduction gear starter with pre-engaged solenoid
- Application: JOHN DEERE Lawn LX173,STX30,STX38 1989-1996
- Net weight: approximately 3.65 kg
- Condition: new, direct replacement for the original unit
A 12V 0.8 kW rating is the output the motor can hold while cranking, not a peak figure. It is sized so the engine reaches starting speed on the first or second revolution, which is what makes a healthy start feel immediate.
The reduction gearset lets the motor run at high speed while the pinion turns slowly with high torque, which is why the unit stays compact enough for a crowded engine bay.
Reference Numbers and Cross References
The following OEM and aftermarket references are listed for this unit:
- 2409801
- 2509809
- 2509808
- 2509811
- E7194-63010
- E7194-63012
- 10455513
- 10455516
- 8000335
- KH-25-098-09-S
- 2509821
- 25-098-08
- 25-098-21-S
- 25-098-08-S
- 25-098-24-S
- 25-098-20
Where the label on the old starter has corroded, compare the pinion teeth, the mounting flange and the terminal bracket with the photographs before ordering. The number on the original unit is the reliable identifier. This starter is listed with 16 references in total.
Where This Starter Is Used
JOHN DEERE Lawn LX173,STX30,STX38 1989-1996 applications in this range share the same mounting pattern and terminal layout, which is why one reference can serve several model years. Fitment is still decided by the starter number rather than by the badge on the vehicle. This applies in particular to the E7194-63010 supplied for JOHN DEERE Lawn LX173,STX30,STX38 1989-1996.
If the number on the old unit falls outside the list above, send the engine code and a photograph of the drive end before ordering. A starter with the correct housing but the wrong pinion will grind on the first attempt and can chip the ring gear.
Common Failure Patterns
Most failures start at the solenoid contact. Each start switches the full cranking current through a copper disc, and after thousands of cycles that disc pits and burns. The result is the familiar single click with no rotation, or a delay before the motor turns.
The brush plate is the second common failure point. Brushes shorten gradually, spring pressure falls, and contact becomes intermittent. Cranking speed drops a little every week until the engine refuses to start on a cold morning. The E7194-63010 is built to the same flange pattern as the unit it replaces.
Symptoms of a Failing Starter
- A single heavy click, then nothing
- Slow, laboured cranking from cold that improves once the engine runs
- Metallic scrape or whine during cranking
- Starter that disengages late, with a brief screech after the engine fires
- Burning smell near the starter after a failed start attempt
A cranking voltage test separates the starter from the rest of the circuit. If battery voltage stays healthy at the terminals but drops sharply at the starter stud, the cable or the connection is at fault rather than the motor. The E7194-63010 ships with its solenoid fitted, so no parts have to be transferred from the old unit.
Checks Before Installation
- Condition of the old pinion and ring gear before the new unit goes in
- Main cable continuity and the condition of the lug at the starter stud
- Battery voltage while cranking, measured at the battery posts
- Mounting face cleanliness and bolt condition
- That the replacement terminal layout matches the original harness
Most comebacks after a starter replacement trace back to something that was not checked before the unit went on: a tired battery, a corroded earth or a chipped ring gear. Ten minutes with a multimeter and a torch prevents the second repair.
Fitting the Replacement
Isolate the battery, mark the terminal positions, then disconnect the main cable and the signal wire. Clean around the mounting flange before the starter is withdrawn so dirt does not fall into the bell housing.
Check the ring gear through the aperture before fitting. Install the new unit with the original bolts, reconnect the cables in the same order and tighten the main terminal without over-stressing the stud. Crank briefly and confirm the pinion releases as the engine fires. The E7194-63010 is built to the same flange pattern as the unit it replaces.
Quality Control and Supply from Hejian Nuojin Auto Parts Co., Ltd.
Each production batch is inspected for housing dimensions, terminal integrity and pinion fit, and every starter is bench tested before it is boxed. Units ship in neutral cartons with foam protection, which keeps freight damage low and allows distributors to label stock under their own brand.
Standard references are held as spot goods, volume orders are delivered in around 30 days, and every unit carries a one-year warranty against manufacturing defects.
Frequently Asked Questions
Should the ring gear be replaced at the same time?
Inspect it, but replace it only when the teeth show damage. A worn ring gear will damage a new pinion within a few starts.
How do I confirm the starter matches my vehicle?
Read the number on the starter body or on the old unit and compare it with the reference list above. Where the label is missing, match the pinion teeth and the terminal bracket against the photographs.
Does the starter need any maintenance?
No routine maintenance is required. Keeping the battery, terminals and earth connections clean is what extends starter life in practice.
Does this starter come with the solenoid?
Yes. The unit is supplied complete with its solenoid, as shown in the product photographs. Mounting bolts are not included.

