
Стартер 24V M105R3060SE для Cummins [YC6LYC] Yuchai 6M и Shangchai 6135 series
Применимый тип:Cummins [YC6LYC] Yuchai 6M и Shangchai 6135 series двигатели 6M320-20
Номер запчасти:M105R3060SE,YC6A24010,YC6A240 STD3524UW,STM3524UW, STM3524WD,STP0225MH,STP2524MH,STP9225MH,STQ3524LP, STQ3524RN, STQ9225CY,STD3524WA, STP0225WA, STP3524RB,STP3524WA,STQ3524WA,X57517200001,M105R3060SE,M105R3015SE, M105R3024SE,VM100R3615SE,VM100R3615SEVPP,STR2321, M34003708100B,L300H3708100,M30153708100,300N10414Z,300N11190Z
| Мощность л.с. : | 24V 7.5KW |
| Число футов : | 11T |
| Размер : | |
| Вес : | Вес нетто 12,4 кг |
| Упаковочные материалы : | Нейтральная упаковка из крафт-бумаги |
| Спотовые / предварительные продажи : | В наличии |
| Гарантия : | 1 год |
| Номер продукта : |
| Тип : | стартер |
| Спецификация : | 24V 7.5KW |
| Число футов : | 11T |
| Марка : | NUOJIN |
| Цифры : | M105R3060SE,YC6A24010,YC6A240 |
| Качество : | НОВЫЙ |
| Время поставки : | 30 дней |





Overview of the M105R3060SE Starter Motor
The M105R3060SE is a 24V, 7.5 kW starter motor supplied for Cummins [YC6LYC] Yuchai 6M and Shangchai 6135 series. A reduction gearset between motor and pinion keeps the body compact while still delivering the cranking torque the engine needs.
Because the motor is only used in short bursts, heat builds up quickly and escapes slowly. A starter that has worked for years in traffic or on site will show heat-hardened resin, shortened brushes and a pitted solenoid contact long before the windings fail.
Specifications at a Glance
- Rated voltage: 24V
- Rated output: 7.5 kW
- Pinion: 11 teeth
- Type: reduction gear starter with pre-engaged solenoid
- Application: Cummins [YC6LYC] Yuchai 6M and Shangchai 6135 series
- Net weight: approximately 12.4 kg
- Condition: new, direct replacement for the original unit
A 24V 7.5 kW rating is the output the motor can hold while cranking, not a peak figure. It is sized so the engine reaches starting speed on the first or second revolution, which is what makes a healthy start feel immediate.
The drive end housing is cast aluminium and carries the pinion bearing, so the pinion stays square to the ring gear when the motor delivers full torque.
Reference Numbers and Cross References
The following OEM and aftermarket references are listed for this unit:
- M105R3060SE
- YC6A24010
- YC6A240
- STD3524UW
- STM3524UW
- STM3524WD
- STP0225MH
- STP2524MH
- STP9225MH
- YC6LYC
- 6M320-20
- STQ3524LP
- STQ3524RN
- STQ9225CY
- STD3524WA
- STP0225WA
Starter suppliers revised this design more than once during production. Confirm the number on the old unit, or send a photograph of the drive end, before committing to an order. This starter is listed with 16 references in total.
Where This Starter Is Used
Cummins [YC6LYC] Yuchai 6M and Shangchai 6135 series applications in this range share the same mounting pattern and terminal layout, which is why one reference can serve several model years. Fitment is still decided by the starter number rather than by the badge on the vehicle. This applies in particular to the M105R3060SE supplied for Cummins [YC6LYC] Yuchai 6M and Shangchai 6135 series.
If the number on the old unit falls outside the list above, send the engine code and a photograph of the drive end before ordering. A starter with the correct housing but the wrong pinion will grind on the first attempt and can chip the ring gear.
Why These Starters Fail
The brush plate is the second common failure point. Brushes shorten gradually, spring pressure falls, and contact becomes intermittent. Cranking speed drops a little every week until the engine refuses to start on a cold morning.
Most failures start at the solenoid contact. Each start switches the full cranking current through a copper disc, and after thousands of cycles that disc pits and burns. The result is the familiar single click with no rotation, or a delay before the motor turns. The M105R3060SE is built to the same flange pattern as the unit it replaces.
Fault Symptoms
- No-crank with a fully charged battery
- Cranking that slows noticeably as the engine bay heats up
- Grinding that disappears on a second attempt
- Whine under load, suggesting a slipping pinion clutch
- Starter that continues to spin for a second after the engine fires
Rule out the simple causes first: battery capacity under load, corroded terminals and the signal wire at the solenoid. A starter that clicks with a known-good battery and a clean signal circuit has an internal contact fault. Fitting the M105R3060SE correctly takes less time than diagnosing the original fault.
Checks Before Installation
- Condition of the old pinion and ring gear before the new unit goes in
- Main cable continuity and the condition of the lug at the starter stud
- Battery voltage while cranking, measured at the battery posts
- Mounting face cleanliness and bolt condition
- That the replacement terminal layout matches the original harness
Fitting a new starter onto a worn ring gear or a marginal battery shortens its life. Check the simple items first, then fit the unit once and correctly.
Fitting the Replacement
Raise and support the vehicle where the starter is reached from below, disconnect the battery, and detach the main cable and signal wire. Note the cable positions before removal so the replacement goes back the same way.
Inspect the ring gear teeth and the mounting face, then fit the replacement and torque the bolts evenly. Reconnect the main cable and signal wire, crank the engine for a moment and listen for clean engagement without a screech or grind. The M105R3060SE ships with its solenoid fitted, so no parts have to be transferred from the old unit.
Quality Control and Supply from Hejian Nuojin Auto Parts Co., Ltd.
Each production batch is inspected for housing dimensions, terminal integrity and pinion fit, and every starter is bench tested before it is boxed. Units ship in neutral cartons with foam protection, which keeps freight damage low and allows distributors to label stock under their own brand.
Standard references are held as spot goods, volume orders are delivered in around 30 days, and every unit carries a one-year warranty against manufacturing defects.
Frequently Asked Questions
Why does the starter work cold but fail when hot?
Heat raises solenoid resistance and reduces brush spring pressure. Both effects build up gradually and appear first on a hot restart.
How long should a replacement starter last?
There is no fixed interval, but a starter fed by a healthy battery and a clean earth path will outlast one that is repeatedly cranked on a low battery.
Can the solenoid be replaced on its own?
Yes, when the motor tests well and only the contact has burnt. On a starter with high mileage the complete unit is usually better value, because the brushes and pinion are close behind.
Does the starter need any maintenance?
No routine maintenance is required. Keeping the battery, terminals and earth connections clean is what extends starter life in practice.

![Стартер 24V M105R3060SE для Cummins [YC6LYC] Yuchai 6M и Shangchai 6135 series](/uploads/260325/4_142059121.jpg)