
Стартер 12V 5.5KW 10T RE502632 для John deere
Применимый тип:for John deere
Номер запчасти:RE523501, RE546027, RE59010, RE683783, RE68783 RE30493, RE503093, RE503120, RE504009 RE507236, RE509025, RE518057, RE518112 IS1056 LRS01535 LRS1535 MS621 1113145 AZF4553 AZF4598 AZJ3190 AZJ3241
| Мощность л.с. : | 12V 5.5KW |
| Число футов : | 10T |
| Размер : | 44*24*20single unit inner box |
| Вес : | Вес нетто 10,3 кг, вес брутто 10,85 кг |
| Упаковочные материалы : | Нейтральная упаковка из крафт-бумаги |
| Спотовые / предварительные продажи : | В наличии |
| Гарантия : | 1 год |
| Номер продукта : |
| Тип : | стартер |
| Спецификация : | 12V 5.5KW |
| Число футов : | 10T |
| Марка : | nuojin |
| Цифры : | RE546027 RE502632 |
| Качество : | НОВЫЙ |
| Время поставки : | 30 дней |





Overview of the RE502632 Starter Motor
This RE502632 starter motor is the 12V, 5.5 kW replacement for John deere applications. The housing, drive end and terminal positions follow the original design, so the unit bolts straight onto the bell housing and reuses the existing cabling.
Cranking load varies with temperature, battery condition and engine condition. A healthy starter has margin for all three; a worn one turns the engine just slowly enough that the control unit hesitates and the driver notices long, laboured starts.
Technical Summary
- Rated voltage: 12V
- Rated output: 5.5 kW
- Pinion: 10 teeth
- Type: reduction gear starter with pre-engaged solenoid
- Application: John deere
- Net weight: approximately 10.85 kg
- Condition: new, direct replacement for the original unit
A 12V 5.5 kW rating is the output the motor can hold while cranking, not a peak figure. It is sized so the engine reaches starting speed on the first or second revolution, which is what makes a healthy start feel immediate.
The drive end housing is cast aluminium and carries the pinion bearing, so the pinion stays square to the ring gear when the motor delivers full torque.
Reference Numbers and Cross References
The reference family for this starter covers the numbers listed here:
- RE502632
- RE509025
- 84994459
- 0001359029
- 0001359058
- 0001359098
- RE523501
- RE546027
- RE59010
- RE683783
- RE68783
- RE30493
- RE503093
- RE503120
- RE504009
- RE507236
Starter suppliers revised this design more than once during production. Confirm the number on the old unit, or send a photograph of the drive end, before committing to an order. This starter is listed with 16 references in total.
Matching the Unit to the Vehicle
This starter family was fitted to a range of John applications, and the part number changed as engines and flywheels were revised. The unit listed here covers the references above and is a direct replacement where those numbers match. Fitting the RE502632 correctly takes less time than diagnosing the original fault.
When ordering for a fleet, quote the starter number from each vehicle rather than a single model reference; mixed build dates are common and the starter changed with them.
Common Failure Patterns
Most failures start at the solenoid contact. Each start switches the full cranking current through a copper disc, and after thousands of cycles that disc pits and burns. The result is the familiar single click with no rotation, or a delay before the motor turns.
Oil or coolant mist from a leaking seal finds its way into the drive end housing, mixes with carbon dust and forms a conductive paste. The starter then arcs internally and fails early, whatever its mileage. This applies in particular to the RE502632 supplied for John deere.
What to Look For
- A single heavy click, then nothing
- Slow, laboured cranking from cold that improves once the engine runs
- Metallic scrape or whine during cranking
- Starter that disengages late, with a brief screech after the engine fires
- Burning smell near the starter after a failed start attempt
Rule out the simple causes first: battery capacity under load, corroded terminals and the signal wire at the solenoid. A starter that clicks with a known-good battery and a clean signal circuit has an internal contact fault. Owners of John deere should treat the RE502632 reference list as a starting point, not the final answer.
Checks Before Installation
- State of charge and age of the battery
- Corrosion on the earth strap and the engine-to-body bond
- Pinion tooth count against the ring gear
- Free movement of the new pinion before fitting
- That the signal wire connector seats fully on the solenoid
Most comebacks after a starter replacement trace back to something that was not checked before the unit went on: a tired battery, a corroded earth or a chipped ring gear. Ten minutes with a multimeter and a torch prevents the second repair.
Fitting Guidance
Raise and support the vehicle where the starter is reached from below, disconnect the battery, and detach the main cable and signal wire. Note the cable positions before removal so the replacement goes back the same way.
Check the ring gear through the aperture before fitting. Install the new unit with the original bolts, reconnect the cables in the same order and tighten the main terminal without over-stressing the stud. Crank briefly and confirm the pinion releases as the engine fires. This applies in particular to the RE502632 supplied for John deere.
Quality Control and Supply from Hejian Nuojin Auto Parts Co., Ltd.
Hejian Nuojin Auto Parts Co., Ltd. manufactures starter and alternator components for the aftermarket. Every unit is bench tested for no-load current draw, solenoid pull-in and release voltage, pinion throw and running noise before packing.
Common references are kept in stock for fast dispatch, volume orders are delivered in around 30 days and each starter carries a one-year warranty against manufacturing defects.
Frequently Asked Questions
How do I confirm the starter matches my vehicle?
Read the number on the starter body or on the old unit and compare it with the reference list above. Where the label is missing, match the pinion teeth and the terminal bracket against the photographs.
How long should a replacement starter last?
There is no fixed interval, but a starter fed by a healthy battery and a clean earth path will outlast one that is repeatedly cranked on a low battery.
Should the ring gear be replaced at the same time?
Inspect it, but replace it only when the teeth show damage. A worn ring gear will damage a new pinion within a few starts.
Can I test the starter on the bench?
Yes. Apply battery voltage to the main stud and the signal terminal and check that the pinion throws and the motor turns. A clamp meter reading against the rated current will show whether the unit is drawing too much.
Detailed vehicle Application
| Make | Model | Year | Engine |
| Case | CS660 | 2004-2015 | Cummins 8.3 TAA, 209kW, 6-cyl |
| Cummins Engines | ISB Series | 1998-2015 | |
| John Deere | 6403 | 2002-2005 | 4045T, 4.5L |
| John Deere | 8000 Laborer | 1996-2003 | John Deere |
| Prairie | 4800 Sprayer | 1993-1997 | Perkins |
| Prairie | 4900 Sprayer | 1993-1997 | Perkins |
| Vermeer | BC1230A Brush Chipper | 1998-2010 | 1004.40T, 4.4L |
| Vermeer | BC1250 Brush Chipper | 1996-2008 | 4.236 |
| Vermeer | BC1250A Brush Chipper | 1998-2010 | 1004.40T, 4.4L |
| Vermeer | BC1600A Brush Chipper | 1991-2003 | 4.236 |
| Vermeer | BC1800A Brush Chipper | 1997-2012 | 1004.40T, 4.4L |
| Vermeer | SC1102 Stump Cutter | 1995-2008 | 4.236 |

