
Стартер 12V 2.8KW 10T RE62916 для John Deere
Применимый тип:John Deere
Номер запчасти:RE62916, 35258820,10461471.10479628, 113011,SE501400.TY24305,STD3011BA ,STD3011CL,STD3011ML STD3011NB,STD3011NL,STD3011WA 508438.6601N RE19196 RE62916, 35258820
| Мощность л.с. : | 12V 2.8KW |
| Число футов : | 10T |
| Размер : | |
| Вес : | Вес нетто 7,7 кг |
| Упаковочные материалы : | Нейтральная упаковка из крафт-бумаги |
| Спотовые / предварительные продажи : | В наличии |
| Гарантия : | 1 год |
| Номер продукта : |
| Тип : | стартер |
| Спецификация : | 12V 2.8KW |
| Число футов : | 10T |
| Марка : | NUOJIN |
| Цифры : | RE62916, 35258820 |
| Качество : | НОВЫЙ |
| Время поставки : | 30 дней |





Overview of the RE62916 Starter Motor
The RE62916 starter motor is a 12V, 2.8 kW unit built for John Deere. It is a reduction-gear starter with a pre-engaged solenoid, assembled to the original mounting flange and terminal positions so it fits without adapters or wiring changes.
Cranking load varies with temperature, battery condition and engine condition. A healthy starter has margin for all three; a worn one turns the engine just slowly enough that the control unit hesitates and the driver notices long, laboured starts.
Technical Summary
- Rated voltage: 12V
- Rated output: 2.8 kW
- Pinion: 10 teeth
- Type: reduction gear starter with pre-engaged solenoid
- Application: John Deere
- Net weight: approximately 7.7 kg
- Condition: new, direct replacement for the original unit
A 12V 2.8 kW rating is the output the motor can hold while cranking, not a peak figure. It is sized so the engine reaches starting speed on the first or second revolution, which is what makes a healthy start feel immediate.
The drive end housing is cast aluminium and carries the pinion bearing, so the pinion stays square to the ring gear when the motor delivers full torque.
Reference Numbers and Cross References
The following OEM and aftermarket references are listed for this unit:
- RE62916
- 35258820
- 10461471.10479628
- 113011
- SE501400.TY24305
- STD3011BA
- STD3011CL
- STD3011ML
- STD3011NB
- STD3011NL
- STD3011WA
- 508438.6601N
Starter suppliers revised this design more than once during production. Confirm the number on the old unit, or send a photograph of the drive end, before committing to an order. This starter is listed with 12 references in total.
Where This Starter Is Used
John Deere applications in this range share the same mounting pattern and terminal layout, which is why one reference can serve several model years. Fitment is still decided by the starter number rather than by the badge on the vehicle. Where a RE62916 has been replaced before, check that the fitted unit still matches the reference list.
Vehicles that have had an engine or gearbox replacement may already carry a different starter from the one the catalogue expects, so treat the paperwork as a starting point rather than the final answer.
What Wears Out First
Oil or coolant mist from a leaking seal finds its way into the drive end housing, mixes with carbon dust and forms a conductive paste. The starter then arcs internally and fails early, whatever its mileage.
Heat is the underlying cause in most cases. The starter sits close to the exhaust, and after a hot shutdown the solenoid winding and brush plate soak in heat with no airflow. Resin hardens, springs lose tension and the contact oxidises. This applies in particular to the RE62916 supplied for John Deere.
Fault Symptoms
- Cranking that sounds normal but takes longer than it used to
- Several attempts needed before the motor engages
- Black carbon dust inside the drive end housing
- Voltage dip that dims the lights during cranking
- Starter that responds to a tap on the housing but not to the key alone
On a high-mileage vehicle, worn brushes and a burnt solenoid contact usually arrive together. If the motor bench tests well but cranking is still weak in the car, inspect the main cable and earth path before fitting another starter. Owners of John Deere should treat the RE62916 reference list as a starting point, not the final answer.
Pre-Fit Checklist
- State of charge and age of the battery
- Corrosion on the earth strap and the engine-to-body bond
- Pinion tooth count against the ring gear
- Free movement of the new pinion before fitting
- That the signal wire connector seats fully on the solenoid
Fitting a new starter onto a worn ring gear or a marginal battery shortens its life. Check the simple items first, then fit the unit once and correctly.
Installation Procedure
Raise and support the vehicle where the starter is reached from below, disconnect the battery, and detach the main cable and signal wire. Note the cable positions before removal so the replacement goes back the same way.
Check the ring gear through the aperture before fitting. Install the new unit with the original bolts, reconnect the cables in the same order and tighten the main terminal without over-stressing the stud. Crank briefly and confirm the pinion releases as the engine fires. This applies in particular to the RE62916 supplied for John Deere.
Quality Control and Supply from Hejian Nuojin Auto Parts Co., Ltd.
Hejian Nuojin Auto Parts Co., Ltd. manufactures starter and alternator components for the aftermarket. Every unit is bench tested for no-load current draw, solenoid pull-in and release voltage, pinion throw and running noise before packing.
Common references are kept in stock for fast dispatch, volume orders are delivered in around 30 days and each starter carries a one-year warranty against manufacturing defects.
Frequently Asked Questions
Does this starter come with the solenoid?
The starter is supplied as a complete assembly including the solenoid. Reuse the original mounting bolts if they are in good condition.
How do I confirm the starter matches my vehicle?
Compare the original part number first, then check the pinion tooth count and the terminal connector layout. The vehicle model alone is not enough, because more than one starter was fitted during production.
Can the solenoid be replaced on its own?
It is possible, provided the motor draws normal current and the pinion is sound. Where the brushes are already short, replacing the complete starter avoids a second repair within a year.
Why does the starter click but not turn?
Most often the battery is low, a terminal is corroded or the solenoid contact is burnt. Measure battery voltage while the key is turned; a healthy battery that still gives only a click points to the solenoid.
JOHN DEERE CRAWLERS 400G Diesel Engine 1988 450E Diesel 4-219 Engine 1986-1992, FORK LIFT 455E Diesel Engine 1982-1990, 482C Diesel Engine 1987, SPRAYERS 6100 Diesel Engine, 400G Diesel Engine 1992

