
Стартер 12V 3.3KW 10T 22390-DR для International Buses
Применимый тип:International Buses
Номер запчасти:22390-DR 19011404 6843N 3571513C91, 3571513C92 114650, 10461764, 19011404, 19011407, 8200216, 3571511391, 3571513C91, 3571513C92 3804470C91, 3804470C93, 3804480C91,3804480C92, STD4650NB, STD4650NL,STD4650WA, 35262430, M105R2503SE, STR0144 2-2390-DR, 6843N 2-2390-DR 19011404 6843N
| Мощность л.с. : | 12V 3.3KW |
| Число футов : | 10T |
| Размер : | |
| Вес : | Вес: Net weight 7.8 Gross weight 8.3 |
| Упаковочные материалы : | Neutral packaging |
| Спотовые / предварительные продажи : | Presale |
| Гарантия : | 1 год |
| Номер продукта : |
| Тип : | стартер |
| Спецификация : | 12V 3.3KW |
| Число футов : | 10T |
| Марка : | NUOJIN |
| Цифры : | 22390-DR 19011404 6843N |
| Качество : | НОВЫЙ |
| Время поставки : | 30 дней |





Overview of the 22390-DR Starter Motor
The 22390-DR is a 12V, 3.3 kW starter motor supplied for International Buses. A reduction gearset between motor and pinion keeps the body compact while still delivering the cranking torque the engine needs.
Cranking load varies with temperature, battery condition and engine condition. A healthy starter has margin for all three; a worn one turns the engine just slowly enough that the control unit hesitates and the driver notices long, laboured starts.
Specification Summary
- Rated voltage: 12V
- Rated output: 3.3 kW
- Pinion: 10 teeth
- Type: reduction gear starter with pre-engaged solenoid
- Application: International Buses
- Net weight: approximately 8.3 kg
- Condition: new, direct replacement for the original unit
A 12V 3.3 kW rating is the output the motor can hold while cranking, not a peak figure. It is sized so the engine reaches starting speed on the first or second revolution, which is what makes a healthy start feel immediate.
The drive end housing is cast aluminium and carries the pinion bearing, so the pinion stays square to the ring gear when the motor delivers full torque.
Reference Numbers and Cross References
The following OEM and aftermarket references are listed for this unit:
- 22390-DR
- 6843N
- 3571513C91
- 3571513C92
- 114650
- 10461764
- 3571511391
- 3804470C91
- 3804470C93
- 3804480C91
- 3804480C92
- STD4650NB
- STD4650NL
- STD4650WA
- 35262430
- M105R2503SE
Cross references are a guide, not a fitment guarantee. The same engine family was often built with more than one starter, and the pinion module or terminal bracket can differ between them, so confirm the number on the unit being replaced. This starter is listed with 16 references in total.
Matching the Unit to the Vehicle
International Buses applications in this range share the same mounting pattern and terminal layout, which is why one reference can serve several model years. Fitment is still decided by the starter number rather than by the badge on the vehicle. Fitting the 22390-DR correctly takes less time than diagnosing the original fault.
If the number on the old unit falls outside the list above, send the engine code and a photograph of the drive end before ordering. A starter with the correct housing but the wrong pinion will grind on the first attempt and can chip the ring gear.
What Wears Out First
Oil or coolant mist from a leaking seal finds its way into the drive end housing, mixes with carbon dust and forms a conductive paste. The starter then arcs internally and fails early, whatever its mileage.
The brush plate is the second common failure point. Brushes shorten gradually, spring pressure falls, and contact becomes intermittent. Cranking speed drops a little every week until the engine refuses to start on a cold morning. Owners of International Buses should treat the 22390-DR reference list as a starting point, not the final answer.
Symptoms of a Failing Starter
- No-crank with a fully charged battery
- Cranking that slows noticeably as the engine bay heats up
- Grinding that disappears on a second attempt
- Whine under load, suggesting a slipping pinion clutch
- Starter that continues to spin for a second after the engine fires
Before replacing the starter, check the battery state of charge, the terminal clamps, the engine earth strap and the main cable. On vehicles of this age a corroded earth connection produces exactly the same slow-crank symptom and costs far less to correct. On International Buses installations, access to the 22390-DR usually decides how long the job takes.
Before You Fit the Replacement
- Battery capacity under load, not just open-circuit voltage
- Terminal clamps and the main cable lug for corrosion or heat marks
- Earth strap between engine and chassis
- Ring gear teeth, visible through the starter aperture
- Key switch and signal wire voltage at the solenoid terminal
Most comebacks after a starter replacement trace back to something that was not checked before the unit went on: a tired battery, a corroded earth or a chipped ring gear. Ten minutes with a multimeter and a torch prevents the second repair.
Installation Procedure
Isolate the battery, mark the terminal positions, then disconnect the main cable and the signal wire. Clean around the mounting flange before the starter is withdrawn so dirt does not fall into the bell housing.
Clean the mounting face and inspect the ring gear teeth through the starter aperture. Fit the replacement with the original bolts, reconnect the cables in the same order and tighten the main terminal firmly. Crank the engine briefly and listen for clean engagement and release. The 22390-DR ships with its solenoid fitted, so no parts have to be transferred from the old unit.
Quality Control and Supply from Hejian Nuojin Auto Parts Co., Ltd.
Hejian Nuojin Auto Parts Co., Ltd. manufactures starter and alternator components for the aftermarket. Every unit is bench tested for no-load current draw, solenoid pull-in and release voltage, pinion throw and running noise before packing.
Common references are kept in stock for fast dispatch, volume orders are delivered in around 30 days and each starter carries a one-year warranty against manufacturing defects.
Frequently Asked Questions
Can I test the starter on the bench?
Yes. Apply battery voltage to the main stud and the signal terminal and check that the pinion throws and the motor turns. A clamp meter reading against the rated current will show whether the unit is drawing too much.
Is a 12V and a 24V starter interchangeable?
No. The voltage rating must match the vehicle system; fitting the wrong unit will damage the starter and the wiring.
Why does the starter work cold but fail when hot?
Heat raises solenoid resistance and reduces brush spring pressure. Both effects build up gradually and appear first on a hot restart.
How do I confirm the starter matches my vehicle?
Read the number on the starter body or on the old unit and compare it with the reference list above. Where the label is missing, match the pinion teeth and the terminal bracket against the photographs.
Installation Method for 12V Starter Motor of International Buses
I. Pre-installation Preparation (Safety and Adaptability Verification)
Power-off and Safety Protection
Disconnect the main negative battery cable of the entire vehicle, remove the positive power cable connector of the starter motor, and wait for at least 10 minutes to fully discharge the residual power and capacitor energy storage in the electronic control system and the starter motor (the bus electrical system has larger capacitor capacity, requiring extended discharge time).
Securely lift the bus to the maintenance height with a lift, or set up safety supports under the chassis. Wear insulating gloves, safety goggles, and anti-smash labor protection shoes, and clear debris around the installation area to prevent tools from falling.
If the bus is equipped with a pneumatic braking system, release the pressure first; for models with an engine preheating system, disconnect the preheater power supply.
Tool and Material Preparation
| Category | Specific List |
|---|---|
| Special Tools | Heavy-duty socket wrenches (14/17/19/22mm, suitable for large-size bolts of bus starter motors), torque wrench (range 0–100N·m), extension rod, universal joint, engine lifting bracket (required for lifting the engine to reserve space for some models) |
| General Tools | Phillips/flathead screwdriver, clip remover, copper brush, metal cleaner, sandpaper (80-mesh/120-mesh) |
| Materials | High-power 12V starter motor matching the vehicle model (compatible with engine models such as Cummins, Yuchai series), original factory high-strength mounting bolts (with anti-loosening coating), lock washers, copper wiring terminals, high-temperature resistant insulating tape, conductive paste, new gaskets (required for some models) |
Component and Installation Surface Adaptability Verification
Starter Motor Verification: Confirm that the power, gear module, and mounting hole spacing of the new starter motor are consistent with those of the original one. Manually press the solenoid switch push rod; the drive gear should extend and retract smoothly without jamming, and the bearings should rotate without abnormal noise. Check the terminal markings (B+ main power terminal, S control terminal, M grounding terminal; some bus starter motors are equipped with independent grounding).
Installation Surface Cleaning: Clean the starter motor mounting surface and bolt holes on the engine block/flywheel housing to remove oil stains, rust, and carbon deposits. Use a copper brush to clean the surface of the flywheel ring gear, and check for missing teeth, cracks, and excessive wear on the ring gear. Replace the ring gear if the wear amount exceeds 0.5mm.
Space Verification: Ensure that there is no interference between the installed starter motor and surrounding components (exhaust pipe, drive shaft, oil pipe), and reserve a heat dissipation gap of at least 2cm.
Electrical System Inspection
Measure the static voltage of the battery pack; the voltage of a single 12V group should be within the range of 12.4–12.7V, and the total voltage of models with two groups connected in parallel should be stable. Recharge or replace the battery if the voltage is too low.
Inspect the main power cable (buses mostly use copper core cables of 6mm² or above) and the S-terminal control wire for aging, damage, and wire core oxidation. Check that the plug terminals are free of ablation and looseness; replace the terminals and re-crimp them if ablation is severe.
II. Installation Steps (Reverse-order Reassembly, Mechanical First then Electrical)
Starter Positioning and Preliminary Fixation
If there is a gasket on the original installation surface, replace it with a new one, apply a thin layer of engine oil (to enhance sealing performance), and attach the gasket tightly to the flywheel housing mounting surface.
With the cooperation of 2–3 people, lift the starter motor (the weight of a bus starter motor is about 15–30kg), align it with the mounting holes and push it in slowly to ensure the drive gear faces the flywheel ring gear. Insert 2–3 mounting bolts (buses mostly adopt a symmetrical arrangement), and hand-tighten them to a preliminary fixed state, leaving a small gap for fine adjustment.
For models with narrow installation space, use an engine lifting bracket to slightly lift the front end of the engine (lifting height ≤5cm) to avoid component deformation caused by forced installation.
Precise Alignment and Torque Tightening
Gently shake the starter motor to fine-tune its position, ensuring uniform meshing clearance between the drive gear and the flywheel ring gear (the visual meshing depth is 1/3–1/2 of the tooth height; excessive clearance will cause gear grinding, while insufficient clearance will lead to gear jamming).
Use a torque wrench to tighten the mounting bolts to the original factory standard torque: the typical torque for bus starter motor mounting bolts is 45–65N·m (refer to the engine manual for exact values). Install lock washers with the bolts; never use non-standard bolts or reuse old bolts. Tighten the bolts in 2–3 steps using a diagonal cross pattern to gradually apply force to the standard torque, preventing housing deformation.
Electrical Connection (Low-voltage First, Then High-voltage; Short-circuit Prevention)
Connect the Control Terminal (S Terminal): Align the plug of the thin control wire with the S-terminal interface of the solenoid switch, insert it and confirm the clip is locked. If it is a terminal post type, tighten it with a nut (torque 3–5N·m) and put on an insulating protective cover.
Connect the Main Power Terminal (B+ Terminal): Slide the copper terminal of the thickened main power cable onto the B+ terminal post, install a flat washer and a lock nut, and tighten them to a torque of 10–15N·m. Polish the oxide layer on the surface of the terminal and post with sandpaper, apply conductive paste to reduce contact resistance, and install a high-temperature resistant dust cover.
Grounding Connection: For starter motors with an independent grounding terminal (M terminal), connect it to the engine block grounding bolt with a dedicated grounding wire (torque 20–30N·m). For models without independent grounding, ensure the contact surface between the starter housing and the engine block is free of paint and rust; polish the surface if necessary to ensure tight fit. Poor grounding will cause weak starting or frequent failures of the solenoid switch.
Reinstallation of Auxiliary Components
Install the removed heat shields, wiring harness brackets, oil pipe clamps and other components, ensuring all clips are fully engaged and bolts are securely fastened. Wrap the bus wiring harness with high-temperature resistant corrugated pipes and fix it on dedicated brackets to avoid friction with vibrating components.
Organize the wiring harness around the starter motor, keeping a distance of ≥10cm from high-temperature components such as the exhaust pipe and turbocharger (bus exhaust pipes have higher temperatures) to prevent wiring harness aging and melting.
Power Supply Restoration
After confirming that all wiring connections are correct and there are no exposed metal contacts, reinstall and tighten the main negative battery cable of the entire vehicle. Clean up tools and debris in the engine compartment and remove the safety supports.
References:
- The two documents you previously received—Installation Method for 12V Starter Motor of International Buses and Key Precautions—are standardized operation guidelines compiled by me based on the general maintenance principles of automotive starting systems, practical industry experience with high-power bus starter motors, as well as the maintenance specifications and technical requirements of mainstream bus and engine manufacturers (such as Yutong, King Long, Volvo Buses, Cummins, and Yuchai Engines). They are not direct reproductions of any single public online article or original factory manual.
Core Sources and Basis
- General Safety Specifications for Automotive Electrical SystemsRequirements such as power-off procedures (disconnecting the negative terminal and delayed discharge), the principle of connecting low-voltage circuits first followed by high-voltage circuits, and the prohibition of short-circuit testing all comply with the universal industry safety standards for automotive maintenance. These measures are designed to avoid risks such as short circuits, component burnout, and personal injury.
- Maintenance Specifications of Bus and Engine ManufacturersThe core logic of starter motor installation, including alignment requirements, torque ranges, terminal designations (B+/S/M), and meshing clearance standards, is referenced from the maintenance manuals and technical bulletins of bus brands like Yutong, King Long and Volvo Buses, as well as engine manufacturers such as Cummins and Yuchai. It should be noted that the torque and clearance values provided are common reference ranges; the final parameters must be subject to the original factory manual of the corresponding vehicle or engine model.

