
Стартер 12V 3KW 11T C490BPG для Xinchai C490BPG
Применимый тип:Xinchai C490BPG
Номер запчасти:QDJ1309K-P 490B510003 STQ3661LC
| Мощность л.с. : | 12V 3 kw |
| Число футов : | 11T |
| Размер : | |
| Вес : | Вес нетто 6,8 кг |
| Упаковочные материалы : | Нейтральная упаковка из крафт-бумаги |
| Спотовые / предварительные продажи : | В наличии |
| Гарантия : | 1 год |
| Номер продукта : |
| Тип : | стартер |
| Спецификация : | 12V 3 kw |
| Число футов : | 11T |
| Марка : | NUOJIN |
| Цифры : | QDJ1309K-P |
| Качество : | НОВЫЙ |
| Время поставки : | 30 дней |





Overview of the C490BPG Starter Motor
The C490BPG starter motor is a 12V, 3 kW unit built for Xinchai C490BPG. It is a reduction-gear starter with a pre-engaged solenoid, assembled to the original mounting flange and terminal positions so it fits without adapters or wiring changes.
The starter carries the full cranking current through its brushes and solenoid contact, so every start costs a little material. That is why the unit is normally replaced once, at the end of a long service life, rather than repaired repeatedly.
Specification Summary
- Rated voltage: 12V
- Rated output: 3 kW
- Pinion: 11 teeth
- Type: reduction gear starter with pre-engaged solenoid
- Application: Xinchai C490BPG
- Net weight: approximately 6.8 kg
- Condition: new, direct replacement for the original unit
A 12V 3 kW rating is the output the motor can hold while cranking, not a peak figure. It is sized so the engine reaches starting speed on the first or second revolution, which is what makes a healthy start feel immediate.
A pre-engaged solenoid pushes the pinion into mesh before the main contact closes, which prevents the tooth damage that occurs when a motor spins up against a stationary ring gear.
Reference Numbers and Cross References
The starter is supplied against the following references, which help identify it against the unit already fitted to the vehicle:
- C490BPG
- QDJ1309K-P
- 490B510003
- STQ3661LC
Starter suppliers revised this design more than once during production. Confirm the number on the old unit, or send a photograph of the drive end, before committing to an order. This starter is listed with 4 references in total.
Application Notes
Xinchai C490BPG applications in this range share the same mounting pattern and terminal layout, which is why one reference can serve several model years. Fitment is still decided by the starter number rather than by the badge on the vehicle. On Xinchai C490BPG installations, access to the C490BPG usually decides how long the job takes.
If the number on the old unit falls outside the list above, send the engine code and a photograph of the drive end before ordering. A starter with the correct housing but the wrong pinion will grind on the first attempt and can chip the ring gear.
What Wears Out First
Oil or coolant mist from a leaking seal finds its way into the drive end housing, mixes with carbon dust and forms a conductive paste. The starter then arcs internally and fails early, whatever its mileage.
The brush plate is the second common failure point. Brushes shorten gradually, spring pressure falls, and contact becomes intermittent. Cranking speed drops a little every week until the engine refuses to start on a cold morning. Where a C490BPG has been replaced before, check that the fitted unit still matches the reference list.
What to Look For
- Cranking that sounds normal but takes longer than it used to
- Several attempts needed before the motor engages
- Black carbon dust inside the drive end housing
- Voltage dip that dims the lights during cranking
- Starter that responds to a tap on the housing but not to the key alone
Before replacing the starter, check the battery state of charge, the terminal clamps, the engine earth strap and the main cable. On vehicles of this age a corroded earth connection produces exactly the same slow-crank symptom and costs far less to correct. Fitting the C490BPG correctly takes less time than diagnosing the original fault.
What to Check Before Fitting
- State of charge and age of the battery
- Corrosion on the earth strap and the engine-to-body bond
- Pinion tooth count against the ring gear
- Free movement of the new pinion before fitting
- That the signal wire connector seats fully on the solenoid
Fitting a new starter onto a worn ring gear or a marginal battery shortens its life. Check the simple items first, then fit the unit once and correctly.
Fitting the Replacement
Disconnect the battery negative terminal, remove the intake parts that restrict access, then disconnect the main cable and the solenoid signal connector. Support the starter before removing the mounting bolts.
Check the ring gear through the aperture before fitting. Install the new unit with the original bolts, reconnect the cables in the same order and tighten the main terminal without over-stressing the stud. Crank briefly and confirm the pinion releases as the engine fires. The C490BPG is built to the same flange pattern as the unit it replaces.
Quality Control and Supply from Hejian Nuojin Auto Parts Co., Ltd.
Hejian Nuojin Auto Parts Co., Ltd. manufactures starter and alternator components for the aftermarket. Every unit is bench tested for no-load current draw, solenoid pull-in and release voltage, pinion throw and running noise before packing.
Common references are kept in stock for fast dispatch, volume orders are delivered in around 30 days and each starter carries a one-year warranty against manufacturing defects.
Frequently Asked Questions
Should the ring gear be replaced at the same time?
Only if teeth are chipped, worn to a step or missing. Inspect the ring gear through the starter aperture before fitting the new unit.
Is a 12V and a 24V starter interchangeable?
No. The voltage rating must match the vehicle system; fitting the wrong unit will damage the starter and the wiring.
How long should a replacement starter last?
There is no fixed interval, but a starter fed by a healthy battery and a clean earth path will outlast one that is repeatedly cranked on a low battery.
Does the starter need any maintenance?
No routine maintenance is required. Keeping the battery, terminals and earth connections clean is what extends starter life in practice.

