
Стартер 12V 3KW 11T QDJ1309K-P для New Chai
Применимый тип:New Chai
Номер запчасти:3001209564,QDJ1309K,QDJ158X 490B-51000 QD1315X CST38103 SQD1000 CST38103AS SQD1000R CST38103GS
| Мощность л.с. : | 12V 24V 3kW |
| Число футов : | 11T |
| Размер : | |
| Вес : | Вес нетто 6,95 кг |
| Упаковочные материалы : | Нейтральная упаковка из крафт-бумаги |
| Спотовые / предварительные продажи : | Presale |
| Гарантия : | 1 год |
| Номер продукта : |
| Тип : | стартер |
| Спецификация : | 12V 24V 3kW |
| Число футов : | 11T |
| Марка : | NUOJIN |
| Цифры : | QDJ1309K-P |
| Качество : | НОВЫЙ |
| Время поставки : | 30 дней |





Overview of the QDJ1309K-P Starter Motor
The QDJ1309K-P starter motor is a 12V, 3 kW unit built for New Chai. It is a reduction-gear starter with a pre-engaged solenoid, assembled to the original mounting flange and terminal positions so it fits without adapters or wiring changes.
Cranking load varies with temperature, battery condition and engine condition. A healthy starter has margin for all three; a worn one turns the engine just slowly enough that the control unit hesitates and the driver notices long, laboured starts.
Technical Summary
- Rated voltage: 12V
- Rated output: 3 kW
- Pinion: 11 teeth
- Type: reduction gear starter with pre-engaged solenoid
- Application: New Chai
- Condition: new, direct replacement for the original unit
A 12V 3 kW rating is the output the motor can hold while cranking, not a peak figure. It is sized so the engine reaches starting speed on the first or second revolution, which is what makes a healthy start feel immediate.
The drive end housing is cast aluminium and carries the pinion bearing, so the pinion stays square to the ring gear when the motor delivers full torque.
Reference Numbers and Cross References
The reference family for this starter covers the numbers listed here:
- QDJ1309K-P
- QDJ1309K
- QDJ158X
- 490B-51000
- QD1315X
- CST38103
- SQD1000
- CST38103AS
- SQD1000R
- CST38103GS
Cross references are a guide, not a fitment guarantee. The same engine family was often built with more than one starter, and the pinion module or terminal bracket can differ between them, so confirm the number on the unit being replaced. This starter is listed with 10 references in total.
Matching the Unit to the Vehicle
This starter is used across New Chai variants that share the same bell housing pattern. Where the original label is missing, the pinion tooth count and terminal position are enough to identify the correct unit. This applies in particular to the QDJ1309K-P supplied for New Chai.
Vehicles that have had an engine or gearbox replacement may already carry a different starter from the one the catalogue expects, so treat the paperwork as a starting point rather than the final answer.
Why These Starters Fail
The brush plate is the second common failure point. Brushes shorten gradually, spring pressure falls, and contact becomes intermittent. Cranking speed drops a little every week until the engine refuses to start on a cold morning.
Most failures start at the solenoid contact. Each start switches the full cranking current through a copper disc, and after thousands of cycles that disc pits and burns. The result is the familiar single click with no rotation, or a delay before the motor turns. Fitting the QDJ1309K-P correctly takes less time than diagnosing the original fault.
Fault Symptoms
- Click from the solenoid with no rotation, sometimes clearing on a second attempt
- Cranking that has become slower over several weeks
- Grinding as the pinion meets the ring gear
- Starter that keeps running after the key is released
- Intermittent no-crank that appears when the engine bay is hot
A cranking voltage test separates the starter from the rest of the circuit. If battery voltage stays healthy at the terminals but drops sharply at the starter stud, the cable or the connection is at fault rather than the motor. This applies in particular to the QDJ1309K-P supplied for New Chai.
What to Check Before Fitting
- Battery capacity under load, not just open-circuit voltage
- Terminal clamps and the main cable lug for corrosion or heat marks
- Earth strap between engine and chassis
- Ring gear teeth, visible through the starter aperture
- Key switch and signal wire voltage at the solenoid terminal
Most comebacks after a starter replacement trace back to something that was not checked before the unit went on: a tired battery, a corroded earth or a chipped ring gear. Ten minutes with a multimeter and a torch prevents the second repair.
Fitting the Replacement
With the battery isolated, remove any heat shield or ducting that blocks access and disconnect the main cable and solenoid connector. Support the unit before the mounting bolts come out; these starters are heavy enough to damage surrounding parts if they drop.
Check the ring gear through the aperture before fitting. Install the new unit with the original bolts, reconnect the cables in the same order and tighten the main terminal without over-stressing the stud. Crank briefly and confirm the pinion releases as the engine fires. Where a QDJ1309K-P has been replaced before, check that the fitted unit still matches the reference list.
Quality Control and Supply from Hejian Nuojin Auto Parts Co., Ltd.
Hejian Nuojin Auto Parts Co., Ltd. manufactures starter and alternator components for the aftermarket. Every unit is bench tested for no-load current draw, solenoid pull-in and release voltage, pinion throw and running noise before packing.
Common references are kept in stock for fast dispatch, volume orders are delivered in around 30 days and each starter carries a one-year warranty against manufacturing defects.
Frequently Asked Questions
Does the starter need any maintenance?
No routine maintenance is required. Keeping the battery, terminals and earth connections clean is what extends starter life in practice.
Is a 12V and a 24V starter interchangeable?
No. The voltage rating must match the vehicle system; fitting the wrong unit will damage the starter and the wiring.
How do I confirm the starter matches my vehicle?
Compare the original part number first, then check the pinion tooth count and the terminal connector layout. The vehicle model alone is not enough, because more than one starter was fitted during production.
Why does the starter work cold but fail when hot?
Heat raises solenoid resistance and reduces brush spring pressure. Both effects build up gradually and appear first on a hot restart.
I. Core Specifications
II. Applicable Engines (Mainstream)
III. Applicable Models (Mainly Forklifts / Agricultural Machinery / Light Trucks)
ances.
ances.

