
Стартер 12V 3.2KW 11T QDJ158X для Xinchai и Quanchai 490 forklift starters
Применимый тип:Xinchai и Quanchai 490 forklift starters
Номер запчасти:QDJ158X 490B-51000
| Мощность л.с. : | 12V 3.2KW |
| Число футов : | 11T |
| Размер : | 24*12*16single unit inner box |
| Вес : | Вес нетто 7,5 кг |
| Упаковочные материалы : | Нейтральная упаковка из крафт-бумаги |
| Спотовые / предварительные продажи : | В наличии |
| Гарантия : | 1 год |
| Номер продукта : |
| Тип : | стартер |
| Спецификация : | 12V 3.2KW |
| Число футов : | 11T |
| Марка : | NUOJIN |
| Цифры : | QDJ158X 490B-51000 |
| Качество : | НОВЫЙ |
| Время поставки : | 10 дней |





Overview of the QDJ158X Starter Motor
The QDJ158X starter motor is a 12V, 3.2 kW unit built for Xinchai and Quanchai 490 forklift starters. It is a reduction-gear starter with a pre-engaged solenoid, assembled to the original mounting flange and terminal positions so it fits without adapters or wiring changes.
The starter carries the full cranking current through its brushes and solenoid contact, so every start costs a little material. That is why the unit is normally replaced once, at the end of a long service life, rather than repaired repeatedly.
Specifications at a Glance
- Rated voltage: 12V
- Rated output: 3.2 kW
- Pinion: 11 teeth
- Type: reduction gear starter with pre-engaged solenoid
- Application: Xinchai and Quanchai 490 forklift starters
- Net weight: approximately 7.5 kg
- Condition: new, direct replacement for the original unit
A 12V 3.2 kW rating is the output the motor can hold while cranking, not a peak figure. It is sized so the engine reaches starting speed on the first or second revolution, which is what makes a healthy start feel immediate.
A pre-engaged solenoid pushes the pinion into mesh before the main contact closes, which prevents the tooth damage that occurs when a motor spins up against a stationary ring gear.
Reference Numbers and Cross References
The following OEM and aftermarket references are listed for this unit:
- QDJ158X
- 490B-51000
Where the label on the old starter has corroded, compare the pinion teeth, the mounting flange and the terminal bracket with the photographs before ordering. The number on the original unit is the reliable identifier. This starter is listed with 2 references in total.
Application Notes
This starter is used across Xinchai and Quanchai 490 forklift starters variants that share the same bell housing pattern. Where the original label is missing, the pinion tooth count and terminal position are enough to identify the correct unit. Because the QDJ158X reuses the original bolts and connectors, no adapters are needed on Xinchai and Quanchai 490 forklift starters.
If the number on the old unit falls outside the list above, send the engine code and a photograph of the drive end before ordering. A starter with the correct housing but the wrong pinion will grind on the first attempt and can chip the ring gear.
Why These Starters Fail
The brush plate is the second common failure point. Brushes shorten gradually, spring pressure falls, and contact becomes intermittent. Cranking speed drops a little every week until the engine refuses to start on a cold morning.
Heat is the underlying cause in most cases. The starter sits close to the exhaust, and after a hot shutdown the solenoid winding and brush plate soak in heat with no airflow. Resin hardens, springs lose tension and the contact oxidises. On Xinchai and Quanchai 490 forklift starters installations, access to the QDJ158X usually decides how long the job takes.
Diagnostic Signs
- No-crank with a fully charged battery
- Cranking that slows noticeably as the engine bay heats up
- Grinding that disappears on a second attempt
- Whine under load, suggesting a slipping pinion clutch
- Starter that continues to spin for a second after the engine fires
Rule out the simple causes first: battery capacity under load, corroded terminals and the signal wire at the solenoid. A starter that clicks with a known-good battery and a clean signal circuit has an internal contact fault. This applies in particular to the QDJ158X supplied for Xinchai and Quanchai 490 forklift starters.
What to Check Before Fitting
- Battery capacity under load, not just open-circuit voltage
- Terminal clamps and the main cable lug for corrosion or heat marks
- Earth strap between engine and chassis
- Ring gear teeth, visible through the starter aperture
- Key switch and signal wire voltage at the solenoid terminal
Fitting a new starter onto a worn ring gear or a marginal battery shortens its life. Check the simple items first, then fit the unit once and correctly.
Installation Notes
Isolate the battery, mark the terminal positions, then disconnect the main cable and the signal wire. Clean around the mounting flange before the starter is withdrawn so dirt does not fall into the bell housing.
After fitting, confirm the pinion returns freely and the cables are clear of the exhaust. Crank once before the first drive, then re-check the main terminal for tightness after the first heat cycle. Because the QDJ158X reuses the original bolts and connectors, no adapters are needed on Xinchai and Quanchai 490 forklift starters.
Quality Control and Supply from Hejian Nuojin Auto Parts Co., Ltd.
Each production batch is inspected for housing dimensions, terminal integrity and pinion fit, and every starter is bench tested before it is boxed. Units ship in neutral cartons with foam protection, which keeps freight damage low and allows distributors to label stock under their own brand.
Standard references are held as spot goods, volume orders are delivered in around 30 days, and every unit carries a one-year warranty against manufacturing defects.
Frequently Asked Questions
Why does the starter work cold but fail when hot?
Heat raises solenoid resistance and reduces brush spring pressure. Both effects build up gradually and appear first on a hot restart.
Can the solenoid be replaced on its own?
Yes, when the motor tests well and only the contact has burnt. On a starter with high mileage the complete unit is usually better value, because the brushes and pinion are close behind.
Does this starter come with the solenoid?
The starter is supplied as a complete assembly including the solenoid. Reuse the original mounting bolts if they are in good condition.
Does the starter need any maintenance?
No routine maintenance is required. Keeping the battery, terminals and earth connections clean is what extends starter life in practice.

