
Стартер 24V 4.5KW 11T QDJ2519B-P для Yunnei 490 , YN27 , YN27CRD
Применимый тип:Yunnei 490 / YN27 / YN27CRD
Номер запчасти:QDJ2519-P QDJ2519B-P SHA5126 SHA5110 SHA5101V
| Мощность л.с. : | 24V 4.5KW |
| Число футов : | 11T |
| Размер : | |
| Вес : | Вес нетто 6,8 кг |
| Упаковочные материалы : | Нейтральная упаковка из крафт-бумаги |
| Спотовые / предварительные продажи : | В наличии |
| Гарантия : | 1 год |
| Номер продукта : |
| Тип : | стартер |
| Спецификация : | 24V 4.5KW |
| Число футов : | 11T |
| Марка : | NUOJIN |
| Цифры : | QDJ2519B-P |
| Качество : | НОВЫЙ |
| Время поставки : | 30 дней |





Overview of the QDJ2519B-P Starter Motor
This QDJ2519B-P starter motor is the 24V, 4.5 kW replacement for Yunnei 490 , YN27 , YN27CRD applications. The housing, drive end and terminal positions follow the original design, so the unit bolts straight onto the bell housing and reuses the existing cabling.
The starter carries the full cranking current through its brushes and solenoid contact, so every start costs a little material. That is why the unit is normally replaced once, at the end of a long service life, rather than repaired repeatedly.
Specification Summary
- Rated voltage: 24V
- Rated output: 4.5 kW
- Pinion: 11 teeth
- Type: reduction gear starter with pre-engaged solenoid
- Application: Yunnei 490 , YN27 , YN27CRD
- Net weight: approximately 6.8 kg
- Condition: new, direct replacement for the original unit
A 24V 4.5 kW rating is the output the motor can hold while cranking, not a peak figure. It is sized so the engine reaches starting speed on the first or second revolution, which is what makes a healthy start feel immediate.
A pre-engaged solenoid pushes the pinion into mesh before the main contact closes, which prevents the tooth damage that occurs when a motor spins up against a stationary ring gear.
Reference Numbers and Cross References
Cross references for this starter are listed below. They are a matching aid rather than a substitute for checking the number on the old unit:
- QDJ2519B-P
- QDJ2519-P
- SHA5126
- SHA5110
- SHA5101V
Starter suppliers revised this design more than once during production. Confirm the number on the old unit, or send a photograph of the drive end, before committing to an order. This starter is listed with 5 references in total.
Where This Starter Is Used
Yunnei 490 , YN27 , YN27CRD applications in this range share the same mounting pattern and terminal layout, which is why one reference can serve several model years. Fitment is still decided by the starter number rather than by the badge on the vehicle. The QDJ2519B-P ships with its solenoid fitted, so no parts have to be transferred from the old unit.
A mismatched pinion is the most common cause of a starter that engages noisily or refuses to mesh. Compare the tooth count before fitting, not after.
What Wears Out First
Oil or coolant mist from a leaking seal finds its way into the drive end housing, mixes with carbon dust and forms a conductive paste. The starter then arcs internally and fails early, whatever its mileage.
Most failures start at the solenoid contact. Each start switches the full cranking current through a copper disc, and after thousands of cycles that disc pits and burns. The result is the familiar single click with no rotation, or a delay before the motor turns. For the QDJ2519B-P, the practical check is the number stamped on the housing.
Symptoms of a Failing Starter
- Click from the solenoid with no rotation, sometimes clearing on a second attempt
- Cranking that has become slower over several weeks
- Grinding as the pinion meets the ring gear
- Starter that keeps running after the key is released
- Intermittent no-crank that appears when the engine bay is hot
A cranking voltage test separates the starter from the rest of the circuit. If battery voltage stays healthy at the terminals but drops sharply at the starter stud, the cable or the connection is at fault rather than the motor. The QDJ2519B-P ships with its solenoid fitted, so no parts have to be transferred from the old unit.
Checks Before Installation
- State of charge and age of the battery
- Corrosion on the earth strap and the engine-to-body bond
- Pinion tooth count against the ring gear
- Free movement of the new pinion before fitting
- That the signal wire connector seats fully on the solenoid
Fitting a new starter onto a worn ring gear or a marginal battery shortens its life. Check the simple items first, then fit the unit once and correctly.
Fitting Guidance
With the battery isolated, remove any heat shield or ducting that blocks access and disconnect the main cable and solenoid connector. Support the unit before the mounting bolts come out; these starters are heavy enough to damage surrounding parts if they drop.
After fitting, confirm the pinion returns freely and the cables are clear of the exhaust. Crank once before the first drive, then re-check the main terminal for tightness after the first heat cycle. The QDJ2519B-P ships with its solenoid fitted, so no parts have to be transferred from the old unit.
Quality Control and Supply from Hejian Nuojin Auto Parts Co., Ltd.
Each production batch is inspected for housing dimensions, terminal integrity and pinion fit, and every starter is bench tested before it is boxed. Units ship in neutral cartons with foam protection, which keeps freight damage low and allows distributors to label stock under their own brand.
Standard references are held as spot goods, volume orders are delivered in around 30 days, and every unit carries a one-year warranty against manufacturing defects.
Frequently Asked Questions
How do I confirm the starter matches my vehicle?
Compare the original part number first, then check the pinion tooth count and the terminal connector layout. The vehicle model alone is not enough, because more than one starter was fitted during production.
Can the solenoid be replaced on its own?
It is possible, provided the motor draws normal current and the pinion is sound. Where the brushes are already short, replacing the complete starter avoids a second repair within a year.
Can I test the starter on the bench?
Yes. Apply battery voltage to the main stud and the signal terminal and check that the pinion throws and the motor turns. A clamp meter reading against the rated current will show whether the unit is drawing too much.
Is a 12V and a 24V starter interchangeable?
No. The voltage rating must match the vehicle system; fitting the wrong unit will damage the starter and the wiring.

