
Стартер 12V 2.7KW 10T C-330M для Sisu Diesel, Ursus
Применимый тип:Sisu Diesel/Ursus
Номер запчасти:0001359124 0001367032 0986013690 0986013691 1369 26284 26342 27512 27512D 27587 27587A D46447500 47920168 LRS00147 LRS00926 LRS147 LRS926 9144722 63227512 836640940 STG0480RB 11130692、11130710、11130897、11131249、 AZJ3234、AZJ3247、AZJ3319、AZJ3405、1S0897 STG0480BW,STG8480BW,STG8480MA STG8480TJ,STG8480XY 9142741.9142748
| Мощность л.с. : | 12V/2.7KW/24V 4.0KW |
| Число футов : | 10T |
| Размер : | 25*16*16cm single unit inner box |
| Вес : | Вес нетто 5,8 кг |
| Упаковочные материалы : | Нейтральная упаковка из крафт-бумаги |
| Спотовые / предварительные продажи : | В наличии |
| Гарантия : | 1 год |
| Номер продукта : |
| Тип : | стартер |
| Спецификация : | 12V/2.7KW/24V 4.0KW |
| Число футов : | 10T |
| Марка : | NUOJIN |
| Цифры : | 9142741 |
| Качество : | НОВЫЙ |
| Время поставки : | 10 дней |





Overview of the C-330M Starter Motor
This C-330M starter motor is the 12V, 2.7 kW replacement for Sisu Diesel, Ursus applications. The housing, drive end and terminal positions follow the original design, so the unit bolts straight onto the bell housing and reuses the existing cabling.
Every unit is bench tested at the factory for current draw, solenoid pull-in and pinion throw, because those three values decide whether a starter works in a cold engine bay as well as it does on a test bench.
Technical Summary
- Rated voltage: 12V
- Rated output: 2.7 kW
- Pinion: 10 teeth
- Type: reduction gear starter with pre-engaged solenoid
- Application: Sisu Diesel, Ursus
- Net weight: approximately 5.8 kg
- Condition: new, direct replacement for the original unit
A 12V 2.7 kW rating is the output the motor can hold while cranking, not a peak figure. It is sized so the engine reaches starting speed on the first or second revolution, which is what makes a healthy start feel immediate.
The reduction gearset lets the motor run at high speed while the pinion turns slowly with high torque, which is why the unit stays compact enough for a crowded engine bay.
Reference Numbers and Cross References
The starter is supplied against the following references, which help identify it against the unit already fitted to the vehicle:
- C-330M
- C-360
- 9142741
- 0001359124
- 0001367032
- 0986013690
- 0986013691
- 27512D
- D46447500
- LRS00147
- LRS00926
- LRS147
- LRS926
- 9144722
- 63227512
- 836640940
Several numbers in this list belong to complete starter assemblies while others refer to the motor only. A visual check of the drive end protects against the most common ordering error. This starter is listed with 16 references in total.
Matching the Unit to the Vehicle
This starter is used across Sisu Diesel, Ursus variants that share the same bell housing pattern. Where the original label is missing, the pinion tooth count and terminal position are enough to identify the correct unit. The C-330M ships with its solenoid fitted, so no parts have to be transferred from the old unit.
If the number on the old unit falls outside the list above, send the engine code and a photograph of the drive end before ordering. A starter with the correct housing but the wrong pinion will grind on the first attempt and can chip the ring gear.
Why These Starters Fail
The brush plate is the second common failure point. Brushes shorten gradually, spring pressure falls, and contact becomes intermittent. Cranking speed drops a little every week until the engine refuses to start on a cold morning.
Heat is the underlying cause in most cases. The starter sits close to the exhaust, and after a hot shutdown the solenoid winding and brush plate soak in heat with no airflow. Resin hardens, springs lose tension and the contact oxidises. On Sisu Diesel, Ursus installations, access to the C-330M usually decides how long the job takes.
Diagnostic Signs
- A single heavy click, then nothing
- Slow, laboured cranking from cold that improves once the engine runs
- Metallic scrape or whine during cranking
- Starter that disengages late, with a brief screech after the engine fires
- Burning smell near the starter after a failed start attempt
A cranking voltage test separates the starter from the rest of the circuit. If battery voltage stays healthy at the terminals but drops sharply at the starter stud, the cable or the connection is at fault rather than the motor. This applies in particular to the C-330M supplied for Sisu Diesel, Ursus.
Pre-Fit Checklist
- State of charge and age of the battery
- Corrosion on the earth strap and the engine-to-body bond
- Pinion tooth count against the ring gear
- Free movement of the new pinion before fitting
- That the signal wire connector seats fully on the solenoid
Fitting a new starter onto a worn ring gear or a marginal battery shortens its life. Check the simple items first, then fit the unit once and correctly.
Installation Notes
Disconnect the battery negative terminal, remove the intake parts that restrict access, then disconnect the main cable and the solenoid signal connector. Support the starter before removing the mounting bolts.
After fitting, confirm the pinion returns freely and the cables are clear of the exhaust. Crank once before the first drive, then re-check the main terminal for tightness after the first heat cycle. Where a C-330M has been replaced before, check that the fitted unit still matches the reference list.
Quality Control and Supply from Hejian Nuojin Auto Parts Co., Ltd.
Each production batch is inspected for housing dimensions, terminal integrity and pinion fit, and every starter is bench tested before it is boxed. Units ship in neutral cartons with foam protection, which keeps freight damage low and allows distributors to label stock under their own brand.
Common references are kept in stock for fast dispatch, volume orders are delivered in around 30 days and each starter carries a one-year warranty against manufacturing defects.
Frequently Asked Questions
Can the solenoid be replaced on its own?
It is possible, provided the motor draws normal current and the pinion is sound. Where the brushes are already short, replacing the complete starter avoids a second repair within a year.
Does the starter need any maintenance?
No routine maintenance is required. Keeping the battery, terminals and earth connections clean is what extends starter life in practice.
How do I confirm the starter matches my vehicle?
Read the number on the starter body or on the old unit and compare it with the reference list above. Where the label is missing, match the pinion teeth and the terminal bracket against the photographs.
How long should a replacement starter last?
Service life depends on starting frequency, battery condition and heat exposure. On a daily-driven vehicle with clean connections, ten years or more is realistic.

