
Стартер 24V 7.5KW 11T QDJ2618 для Renault Kerax, Premium truck
Применимый тип:Renault Kerax, Premium truck (verify двигатель model и OE number before ordering)
Номер запчасти:QDJ2618, D5010508380, 5010508380, 5010508330, 5001853713, 5010306592, 5010480196, 86061, M009T60472, M009T60471, M009T60473, M009T61571, 6-QA-180
| Мощность л.с. : | 24v 7.5kw |
| Число футов : | 11T |
| Размер : | 44*24*19 cm single unit inner box |
| Вес : | Вес нетто 8,9 кг, вес брутто 9,4 кг |
| Упаковочные материалы : | Нейтральная упаковка из крафт-бумаги |
| Спотовые / предварительные продажи : | В наличии |
| Гарантия : | 1 год |
| Номер продукта : |
| Тип : | стартер |
| Спецификация : | 24V 7.5KW |
| Число футов : | 11T |
| Марка : | nuojin |
| Цифры : | QDJ2618 5010508380 |
| Качество : | НОВЫЙ |
| Время поставки : | 10 дней |





Overview of the QDJ2618 Starter Motor
This QDJ2618 starter motor is the 24V, 7.5 kW replacement for Renault Kerax, Premium truck applications. The housing, drive end and terminal positions follow the original design, so the unit bolts straight onto the bell housing and reuses the existing cabling.
Every unit is bench tested at the factory for current draw, solenoid pull-in and pinion throw, because those three values decide whether a starter works in a cold engine bay as well as it does on a test bench.
Specifications at a Glance
- Rated voltage: 24V
- Rated output: 7.5 kW
- Pinion: 11 teeth
- Type: reduction gear starter with pre-engaged solenoid
- Application: Renault Kerax, Premium truck
- Net weight: approximately 9.4 kg
- Condition: new, direct replacement for the original unit
A 24V 7.5 kW rating is the output the motor can hold while cranking, not a peak figure. It is sized so the engine reaches starting speed on the first or second revolution, which is what makes a healthy start feel immediate.
The drive end housing is cast aluminium and carries the pinion bearing, so the pinion stays square to the ring gear when the motor delivers full torque.
Reference Numbers and Cross References
Cross references for this starter are listed below. They are a matching aid rather than a substitute for checking the number on the old unit:
- QDJ2618
- 5010508380
- D5010508380
- 5010508330
- 5001853713
- 5010306592
- 5010480196
- M009T60472
- M009T60471
- M009T60473
- M009T61571
- 6-QA-180
Starter suppliers revised this design more than once during production. Confirm the number on the old unit, or send a photograph of the drive end, before committing to an order. This starter is listed with 12 references in total.
Fitment and Application
The unit is listed for Renault Kerax, Premium truck. Because manufacturers changed starter suppliers during the production run, the safest check is the number stamped on the starter body, not the model year alone. The QDJ2618 ships with its solenoid fitted, so no parts have to be transferred from the old unit.
When ordering for a fleet, quote the starter number from each vehicle rather than a single model reference; mixed build dates are common and the starter changed with them.
What Wears Out First
Oil or coolant mist from a leaking seal finds its way into the drive end housing, mixes with carbon dust and forms a conductive paste. The starter then arcs internally and fails early, whatever its mileage.
The brush plate is the second common failure point. Brushes shorten gradually, spring pressure falls, and contact becomes intermittent. Cranking speed drops a little every week until the engine refuses to start on a cold morning. The QDJ2618 ships with its solenoid fitted, so no parts have to be transferred from the old unit.
Fault Symptoms
- No-crank with a fully charged battery
- Cranking that slows noticeably as the engine bay heats up
- Grinding that disappears on a second attempt
- Whine under load, suggesting a slipping pinion clutch
- Starter that continues to spin for a second after the engine fires
Before replacing the starter, check the battery state of charge, the terminal clamps, the engine earth strap and the main cable. On vehicles of this age a corroded earth connection produces exactly the same slow-crank symptom and costs far less to correct. Owners of Renault Kerax, Premium truck should treat the QDJ2618 reference list as a starting point, not the final answer.
Before You Fit the Replacement
- Condition of the old pinion and ring gear before the new unit goes in
- Main cable continuity and the condition of the lug at the starter stud
- Battery voltage while cranking, measured at the battery posts
- Mounting face cleanliness and bolt condition
- That the replacement terminal layout matches the original harness
Most comebacks after a starter replacement trace back to something that was not checked before the unit went on: a tired battery, a corroded earth or a chipped ring gear. Ten minutes with a multimeter and a torch prevents the second repair.
Fitting Guidance
Isolate the battery, mark the terminal positions, then disconnect the main cable and the signal wire. Clean around the mounting flange before the starter is withdrawn so dirt does not fall into the bell housing.
After fitting, confirm the pinion returns freely and the cables are clear of the exhaust. Crank once before the first drive, then re-check the main terminal for tightness after the first heat cycle. Where a QDJ2618 has been replaced before, check that the fitted unit still matches the reference list.
Quality Control and Supply from Hejian Nuojin Auto Parts Co., Ltd.
Hejian Nuojin Auto Parts Co., Ltd. manufactures starter and alternator components for the aftermarket. Every unit is bench tested for no-load current draw, solenoid pull-in and release voltage, pinion throw and running noise before packing.
Standard references are held as spot goods, volume orders are delivered in around 30 days, and every unit carries a one-year warranty against manufacturing defects.
Frequently Asked Questions
Does this starter come with the solenoid?
The starter is supplied as a complete assembly including the solenoid. Reuse the original mounting bolts if they are in good condition.
Why does the starter work cold but fail when hot?
Heat raises solenoid resistance and reduces brush spring pressure. Both effects build up gradually and appear first on a hot restart.
Does the starter need any maintenance?
No routine maintenance is required. Keeping the battery, terminals and earth connections clean is what extends starter life in practice.
Can the solenoid be replaced on its own?
Yes, when the motor tests well and only the contact has burnt. On a starter with high mileage the complete unit is usually better value, because the brushes and pinion are close behind.

