clutch pressure plate MR111344 MR446367 MR111344 CM-905 MBC613 2304A001 MR446367 MR111344 CM-905 2304A001,M210I34,J2105041 FOR Mitsubishi

Install the pressure plate assembly: Use a guide locator or transmission input shaft for centering to ensure the driven plate is concentric with the pressure plate. Then install the pressure plate on the flywheel, making sure the locating pins of the pressure plate perfectly fit into the locating holes of the flywheel.  •  Secure the pressure plate: The pressure plate must be in close contact with the flywheel and fixed with fastening bolts. When tightening, tighten them sequentially in a diagonal pattern with a tightening torque of 25Nm. Both ends of the release fork shaft must be concentric.  •  Install other components: Install related components such as the release bearing in sequence, ensuring they are properly installed in place.  •  Inspection and adjustment: After installation, adjust the free travel of the clutch pedal to keep it within the range of 15mm to 25mm. Start the engine, check if the clutch operates smoothly, try shifting gears, and ensure everything is normal.

The installation method for the Mitsubishi clutch pressure plate is as follows: •  Preparation work: Park the vehicle on a flat surface and ensure the vehicle is cool and stable. Prepare suitable tools such as a clutch pressure plate, clutch disc, wrench, screwdriver, torque wrench, lubricant, and cleaning cloth.  •  Removing old components: Loosen the fixing bolts of the flywheel, carefully remove the old pressure plate and clutch disc, taking care not to damage surrounding components.  •  Cleaning the installation area: Use a cleaning cloth to carefully clean the flywheel, removing oil stains, dust, and impurities from it to keep the installation surface clean and tidy.Alignment marks: Ensure that the alignment marks on the clutch cover, pressure plate, and diaphragm spring are precisely aligned. Lubrication treatment: During installation, apply basic grease to each fulcrum, bearing surface, and release bearing to reduce friction and wear. Installing the clutch disc: Face the damper disc surface of the clutch disc towards the pressure plate, then align it with the pressure plate so that the guide pins and guide holes fit tightly. Gently rotate the clutch disc to check if it can move freely without any jamming.

The core precautions for installing a Mitsubishi clutch pressure plate are: ensuring component matching, keeping the mounting surfaces clean and concentric, uniformly tightening the bolts diagonally, and ensuring adequate lubrication to avoid problems such as slipping or incomplete disengagement later. Component Matching and Inspection •  The new pressure plate must be fully compatible with the vehicle model. Focus on checking the pressure plate size and diaphragm spring specifications. At the same time, inspect that the pressure plate surface has no warping or cracks, and the diaphragm spring has no deformation or fatigue damage.  •  The matching clutch disc and release bearing need to be inspected simultaneously. If the sinking amount of the clutch disc rivets exceeds 0.3mm, or the release bearing makes abnormal noise during rotation, they must be replaced together.Cleaning and Treatment of Mounting Surfaces •  The mating surfaces of the flywheel and pressure plate must be thoroughly cleaned. Use a clean cloth to wipe off oil stains, rust, and impurities to prevent uneven force on the pressure plate due to an uneven contact surface, which could cause slipping or jitter.  •  If there are slight scratches on the flywheel surface, they can be lightly sanded to make it smooth; if the scratches are deep or the flywheel warpage exceeds 0.2mm, the flywheel must be repaired or replaced first.Positioning and Concentricity Assurance •  During installation, it is necessary to align the original factory positioning marks on the clutch cover, pressure plate, and flywheel to ensure precise fitting of the three components and avoid deviations in power transmission.  •  Use the transmission input shaft or a dedicated guiding tool for positioning to ensure concentricity between the pressure plate and the clutch disc; otherwise, it may lead to difficulty in shifting gears and clutch judder.Bolt tightening requirements •  The fixing bolts must be tightened diagonally in multiple steps gradually to avoid deformation of the pressure plate caused by single tightening. The final tightening torque must strictly follow the vehicle model specifications (usually 25Nm, and some models need to refer to the maintenance manual).  •  Original factory bolts or high-strength bolts of the same specification must be used. A small amount of anti-seize agent can be applied to the threads before installation to prevent loosening later.Lubrication and Assembly Details •  Apply a small amount of high-temperature lithium-based grease only to moving parts such as the release bearing, the fulcrum of the release fork shaft, and the pressure plate locating pins. It is strictly forbidden to get grease on the friction surfaces of the pressure plate or clutch disc, as this will cause clutch slippage.  •  During installation, do not strike the pressure plate or diaphragm spring to avoid damaging the diaphragm spring. Both ends of the release fork shaft must remain concentric to ensure an even release stroke.   Post-Installation Inspection and Testing •  Adjust the clutch pedal free travel to 15-25mm. When the pedal is depressed, it should feel smooth without jamming and return quickly.  •  After starting the engine, depress the clutch pedal multiple times at idle to check for abnormal noises; attempt to shift gears to ensure smooth shifting without gear collision sounds, verifying that the pressure plate and clutch disc engage and disengage properly.

References：The content you mentioned regarding the installation precautions for Mitsubishi clutch pressure plates mainly comes from the relevant Q&A pages on Autohome.These installation precautions are mentioned in multiple Q&A posts on Autohome, such as "How to adjust the clutch of Mitsubishi Pajero?" and "How to set the clutch of Mitsubishi Pajero?" etc. These posts were published between 2024 and 2025, and the specific links are as follows:https://www.autohome.com.cn/ask/10929129.html • https://www.autohome.com.cn/ask/6342619.html • https://www.autohome.com.cn/ask/10118175.html • https://www.autohome.com.cn/ask/15210304.html

In addition, some content on PCauto also covers relevant precautions for the installation of clutch pressure plates, such as "Where is the clutch pressure plate located?" and "What are the precautions for installing the clutch three-piece set?", with the links being:http://m.pcauto.com.cn/baike/1176367/2196358/ • http://www.pcauto.com.cn/jxwd/4763/47630883.html