Clutch kit 618308400 826728，4110002000，618308400，4130002510 4110002510， 4110002820， 4130002011 4130002510，4142102000，618308400 for hyundai Kia

The installation methods for Hyundai-Kia clutch kits are basically the same, but there may be some differences between different models. Here are more detailed installation steps and precautions: • Preparation Work: Prepare common tools such as a jack, wrench, socket, torque wrench, as well as special tools that may be needed, such as a clutch alignment tool. At the same time, carefully check whether all components of the clutch kit are in good condition, and whether there are problems such as wear or deformation. Park the vehicle on a flat and solid ground, pull up the handbrake, and place a triangular warning sign to ensure operational safety.Removing the drive shaft: Lift the vehicle with a jack and support it stably. Generally, it is necessary to support the vehicle at each of its four corners to ensure it does not shake. Locate the connection points of the drive shaft with components such as the gearbox and differential. These connections are usually fixed with bolts or nuts. Gradually loosen and remove these connecting bolts in a diagonal order, then take the drive shaft off the vehicle. During the removal process, be sure to mark properly for accurate reinstallation later. At the same time, be careful of the weight of the drive shaft to avoid it falling and causing injury.Removing the gearbox: Disconnect all connections between the gearbox and the engine, including the shift cable, clutch hydraulic lines (if it is a hydraulic clutch), electrical connections, etc. Then remove the fixing bolts that secure the gearbox to the engine block. The number and positions of these bolts may vary depending on the vehicle model, so you need to carefully locate and remove them one by one. Carefully separate the gearbox from the engine and take it off, then place it in a safe location. Be careful not to excessively pull or damage the surrounding pipes and wires during the removal process.Removing the old clutch kit: Remove the clutch pressure plate and driven plate from the flywheel. The pressure plate is generally fixed to the flywheel with multiple bolts, and these bolts need to be loosened gradually in a diagonal order to prevent the pressure plate from becoming deformed. After removing the pressure plate, take the driven plate off the flywheel. At the same time, check whether the crankshaft pilot bearing is in good condition; if there is a problem, it should be replaced in a timely manner. If the pilot bearing is severely worn, it may cause abnormal clutch operation or damage new clutch components.Installing a new clutch kit: •  Installing the driven plate: Mount the new driven plate onto the flywheel, paying attention to the orientation of the driven plate. Usually, the side with the marking faces the pressure plate, or follow the instructions in the vehicle repair manual for installation. A special tool or the transmission input shaft can be used to align the driven plate with the guide bearing of the transmission shaft, ensuring accurate installation position and preventing the driven plate from shifting or tilting during installation.  •  Installing the pressure plate: Align the pressure plate with the locating pins or holes on the flywheel, then install the pressure plate bolts. Tighten the bolts gradually in a diagonal sequence in multiple steps to reach the specified torque value. The torque for pressure plate bolts may vary among different vehicle models, which is generally clearly stated in the repair manual. For example, the tightening torque of pressure plate bolts for some Kia models ranges from 14.7-21.6N・m.Install the release bearing and related components: First, install the release bearing in the correct position inside the front flywheel housing of the transmission, ensuring it rotates flexibly. Then, install the return spring, accurately connecting its two ends to the corresponding parts to ensure the spring can function properly for returning. If it is a hydraulic clutch, it is also necessary to install related components such as the clutch slave cylinder and connect the hydraulic pipelines properly.  •  Install the gearbox: Carefully install the gearbox back onto the engine, align the connecting parts and tighten the fixing bolts. Then, connect the previously disconnected shift cables, hydraulic pipelines, electrical connections, etc. During the installation of the gearbox, attention should be paid to ensuring that the connection part between the gearbox and the engine is tightly fitted to avoid loosening or misalignment.Install the drive shaft: According to the marks made earlier, accurately reset the drive shaft, install and tighten the connecting bolts. Similarly, tighten them in a diagonal sequence to ensure the drive shaft is firmly connected and balanced.  •  Adjust the clutch clearance: Use a feeler gauge to measure the clutch clearance, and adjust the clutch clearance to the standard value by means such as adjusting the pull rod distance. The standard clutch clearance may vary for different vehicle models, and it is generally clearly specified in the maintenance manual. For example, the standard clearance value for the two sets of clutch plates in some Hyundai and Kia models is around 1 mm. After adjustment, repeatedly press and release the clutch pedal to check the operation of the clutch, ensuring that it disengages completely and engages smoothly.Inspection and Testing: After installation, conduct a comprehensive inspection of the entire clutch system and related components to ensure all parts are securely installed, connections are normal, and there are no issues such as missing bolts or unconnected pipelines. Then start the vehicle and conduct a road test to check the working performance of the clutch, including whether shifting is smooth, whether there is slippage or incomplete disengagement, etc. If any abnormalities are found, they should be promptly identified and resolved.

References：The "passage" you mentioned refers to the previous content about the installation method of Hyundai-Kia clutch kits, right? It does not have a specific single source. These installation methods and precautions are compiled by integrating relevant materials from automobile repair manuals, professional automobile repair websites (such as Pacific Auto Network, Autohome, etc.), as well as the actual operation experience of automobile repair masters. Automobile repair manuals are the main reference source, which contain detailed maintenance and installation steps and technical parameters for various parts of the vehicle. At the same time, there are many maintenance experiences and tips shared by car owners and maintenance personnel on professional websites in the automotive field. When sorting out relevant content, this information will also be screened and integrated to provide users with more comprehensive and accurate installation guidance.