Clutch kit 71793534 46810284 ，71793534，5892775，71741238，5892775 5894334， 71711133 ，71711442，71718691，71752449 71714672 ，71718481， 7171848，571752239， 71784134，for Fiat

Different models of Fiat cars may have slight differences in their clutch installation methods, but the overall steps are roughly the same. Here are the general installation methods for a Fiat clutch:Preparation Work: •  Vehicle Parking and Safety: Park the vehicle on a flat, solid surface, pull up the handbrake, and place a triangular warning sign. If it is necessary to lift the vehicle, use a reliable jack and stands to ensure the vehicle is stably supported, preventing danger caused by the vehicle moving or falling during operation.  •  Tool Preparation: Prepare common tools such as wrenches, screwdrivers, sockets, torque wrenches, etc. Some special tools may also be needed, such as a special tool for fixing the flywheel.  •  Component Inspection: Check the integrity and quality of the new clutch kit to ensure that components such as the clutch disc, pressure plate, and release bearing are free from damage, deformation, or other defects, and verify that their model and specifications match the vehicle.Removing related components: •  Removing the tires: If it is necessary to operate from under the vehicle, the front or rear wheels of the vehicle can be removed first to better access the clutch components.  •  Removing accessories: It may be necessary to remove some accessories that block the operation, such as the air filter, battery and battery tray, starter motor, etc., depending on the vehicle model. At the same time, disconnect the wire harnesses, shift cables, reverse light connectors, etc. related to the transmission.  •  Separating the transmission from the engine: First, loosen the connecting bolts between the transmission and the engine, then separate the transmission from the engine and lower it. Be careful when lowering the transmission to avoid damaging the transmission or other surrounding components.Removing the old clutch: •  Securing the flywheel: Use a special tool to secure the flywheel to prevent it from rotating during the clutch removal process.  •  Removing the pressure plate bolts: Loosen and remove the fixing bolts of the clutch pressure plate step by step in a diagonal order.  •  Taking out the old clutch components: Remove the old clutch pressure plate and clutch disc from the flywheel, and at the same time take out related components such as the release bearing.Cleaning and Inspection: •  Clean the installation site: Clean the flywheel surface, clutch mounting surface and other parts with a clean cloth or solvent to remove oil, dust, rust and impurities, ensuring that the installation surface is clean and flat.  •  Inspect related components: Carefully check whether the flywheel surface has damage such as wear, grooves, cracks, etc. If the flywheel is severely worn or has other problems, it may need to be repaired or replaced; otherwise, it will affect the use effect and service life of the new clutch. At the same time, check whether related components such as the release bearing and transmission input shaft are normal.Install a new clutch: •  Install the clutch disc: Align the new clutch disc with the spline holes on the flywheel, carefully slide it onto the transmission input shaft, and ensure the clutch disc is installed in the correct direction. Usually, there will be relevant installation marks or instructions on the clutch disc.  •  Install the pressure plate: Mount the clutch pressure plate onto the flywheel, align it with the locating pins or holes, then tighten the pressure plate's fixing bolts gradually and evenly in a diagonal sequence. The tightening torque should comply with the vehicle's repair manual specifications, and a torque wrench is generally required to ensure consistent tightening force.  •  Install the release bearing: Correctly install the release bearing onto the release fork or the corresponding mounting position, ensuring it can rotate flexibly. For some vehicle models, an appropriate amount of grease may need to be applied to the surface of the release bearing.Reinstall the transmission and other components: •  Install the transmission: Reinstall the transmission onto the engine, align the connection parts, and tighten the connecting bolts between the transmission and the engine.  •  Restore the wiring harnesses and components: Reconnect the previously disconnected wiring harnesses, shift cables, reverse light connectors, etc., ensuring secure connections, and reinstall the removed accessories such as the air filter, battery and battery tray, starter motor, etc., back to their original positions in sequence.  •  Install the tires: If the tires were removed earlier, install them back at this point, tighten the tire bolts, then lower the vehicle and check if the tire pressure is normal.Debugging and Inspection: •  Adding Fluids: Check and add relevant fluids such as transmission oil to the specified level.  •  Perform Initialization (for some models): For some Fiat models, after replacing the clutch, it is necessary to use a dedicated diagnostic device to initialize or match the vehicle's clutch control system to ensure the clutch works properly.  •  Test Drive Inspection: Start the vehicle, slowly press and release the clutch pedal, and check if the clutch pedal stroke is normal, with no jamming, abnormal resistance, etc. Then engage different gears, take a test drive, and observe if the vehicle starts and shifts smoothly, if power transmission is normal, and if there are any problems such as slipping or abnormal noises.

References：The content you mentioned regarding the precautions for installing a Fiat clutch does not have a clear single specific source. It is compiled by integrating various aspects such as general knowledge in the automotive repair field, the technical characteristics of Fiat vehicles, and the requirements of relevant repair manuals. Some of the content, such as the precaution of not using a grinder to clean the clutch to avoid inhaling asbestos fiber dust, is mentioned in relevant articles on Pacific Auto Network. The precautions about selecting regular accessories and tightening mounting bolts to the specified torque have similar expressions in the content of Pacific Auto Encyclopedia. In addition, some specific requirements during the installation process, such as using special tools to fix the flywheel and paying attention to the installation direction of parts, are consistent with the norms in the actual maintenance operations of Fiat vehicles and the guiding principles in some automotive repair manuals, but it is difficult to specifically point out that they come from a particular official Fiat repair manual or a specific article.