Clutch Kit 41421M1000 for Modern, Mitsubishi
Applicable models:Modern, Mitsubishi
Reference part number:41300-H1010， HQ131111，SHQ131111 S41421M1000 41421M1000，HQ158020 SHQ131101，HR158010 HQ131101 KY-023，ADG030100 KF-598,CP-6080,3000 951 345 07-00178-SX, KY-025,ADG030132 92598, 623 3307 00,3000 951 454，821350, 92-05-598, ICK-5H12 KY023-K,25HY069, 07-00155-SX
| Rated output : | |
| Pulley : | |
| Size : | Outer box size 30+29.5+5 |
| Weight : | Net weight 5.75KG Gross weight 5.9KG |
| Packaging : | Neutral kraft paper packaging |
| Spot/Pre sale : | Spot goods |
| Warranty : | 1 year |
| Product number : |
| Type : | clutch kit |
| Specification : | 225mm |
| Pulley : | |
| Brand : | NUOJIN |
| Number : | 41421M1000 41300H1010 41421M100 |
| Quality : | NEW |
| Delivery time : | 30 days |
41421M1000 Clutch Kit: What It Does
A clutch kit is the practical way to replace a clutch. On the 41421M1000 kit the cover, disc and bearing are matched to each other and to the original flywheel pattern, so the pedal feel and torque capacity stay as designed.
Every unit is checked against the original dimensions before packing. Bolt patterns, diameters and interfaces are matched so the part can be fitted with standard tools.
Specification Summary
- Pressure plate with matched clamp load
- Friction disc with the original spline count
- Release bearing included
- Alignment tool supplied where required
Reference Numbers and Cross References
Match the unit by any of these numbers:
- 41421M1000
- 41300H1010
- 41421M100
- 41300-H1010
- HQ131111
- SHQ131111
- S41421M1000
- HQ158020
- SHQ131101
- HR158010
- HQ131101
- KY-023
- ADG030100
- KF-598
- CP-6080
- 07-00178-SX
Application Notes
The kit fits Modern, Mitsubishi applications. Confirm the diameter, spline count and release type before ordering, and check the flywheel at the same time.
Fitment follows the assembly, not the badge. Two vehicles of the same model year can use different parts, so check the number on the old unit.
Failure Modes
Clutches wear as a set: the disc lining thins, the pressure plate loses clamp load and the bearing loses grease. Replacing only the disc leaves a weak cover and a noisy bearing behind.
Oil contamination and misalignment finish a clutch early. A leaking rear main seal ruins the new lining, and a worn fork makes the new bearing work at an angle.
Fault Symptoms
- Clutch slip under load
- Judder when pulling away
- Noise when the pedal is pressed
- High or low bite point
- Burning smell after hill starts
Checking Before Replacement
Check the release fork, guide sleeve and spigot bearing. These parts are cheap and they decide how the new kit performs.
Inspect the mating surfaces and the fasteners before assembly. Most early failures trace back to something that was not renewed alongside.
Installation Notes
Clean the flywheel, align the disc with the tool supplied, fit the cover and torque the bolts in a cross pattern. Fit the new bearing, check pedal free play, then bed the clutch in gently for the first few hundred kilometres.
Related Parts to Check at the Same Time
- Flywheel
- Release fork and guide sleeve
- Spigot bearing
- Clutch cable or release cylinder
Quality Control and Supply
Hejian Nuojin Auto Parts Co., Ltd. inspects dimensions, materials and interfaces on every batch, then packs the parts in neutral cartons. Each unit carries a one-year warranty against manufacturing defects.
Frequently Asked Questions
Why did the original part fail?
Wear, heat and misalignment account for most failures. Correct installation and matching numbers prevent a repeat.
Is a warranty included?
Yes, one year against manufacturing defects, with neutral packing for resale.
How do I confirm the part number?
Read the number from the old unit, not from a catalogue illustration. Compare the key dimensions at the same time.
Can I fit this without special tools?
Most of these parts fit with standard hand tools. A pulley needs a spline holding tool, and a clutch needs an alignment tool.
