Installation Method for SAIC Wuling Hongguang 12V 75A Generator

I. Pre-installation Preparation

1. Tool and Consumable Preparation

2. Accessory and Equipment Inspection

• Confirm that the generator model is compatible with Wuling Hongguang (verify the part number). Check for no cracks on the surface, no corrosion on terminals, and smooth rotation of the pulley without abnormal noise.

• Inspect that supporting accessories such as brackets, bolts, and terminals meet original factory specifications and are free from deformation or damage.

• Use a multimeter to measure the excitation winding resistance (reference value: 2-5Ω) and an insulation resistance tester to measure the winding insulation resistance (≥1MΩ) to confirm no open circuit, short circuit, or poor insulation.

3. Pre-vehicle Preparation

• Park the vehicle on a flat surface, engage the parking brake, turn off the engine, and disconnect the negative battery cable (to prevent short circuits).

• Clean oil stains and dust from the installation area. Check the condition of engine brackets, belt tensioners, and crankshaft pulleys; replace damaged components promptly.

II. Removal of the Old Generator (if replacing)

1. Remove the belt: Pry the tensioner with a wrench, remove the drive belt, take photos to record the belt routing, and remove the belt guard.

2. Disconnect wiring: Remove the B+ terminal power cable, F/L terminal excitation cable, and ground cable in sequence, and mark them clearly to avoid incorrect connection.

3. Remove bolts: First loosen the generator pivot bolt, then remove the adjustment bracket bolt, and take out the old generator.

III. New Generator Installation Process

1. Install the Generator Body

1. Place the new generator on the mounting bracket and pre-tighten the pivot bolt and adjustment bracket bolt (do not fully tighten temporarily).

2. Adjust the generator position to ensure the pulley, crankshaft pulley, and tensioner pulley are on the same plane (deviation ≤1mm) to prevent belt misalignment.

3. Tighten the bolts to the specified torque with a torque wrench: pivot bolt 25-35N·m, adjustment bracket bolt 15-20N·m. Apply a small amount of high-temperature threadlocker to the bolts to prevent loosening.

2. Install the Drive Belt

1. Install the belt according to the recorded routing, ensuring it is fully seated in the grooves of each pulley.

2. Pry the tensioner to adjust belt tightness: press the midpoint of the belt with a force of 30-50N, and the deflection should be 10-15mm; for automatic tensioners, directly reset and confirm no slipping.

3. Reinstall the belt guard.

3. Wiring Operation

1. Treat terminals: Polish the oxide layer with sandpaper and apply conductive paste to improve conductivity.

2. Connect power cable: Connect the positive battery cable to the B+ terminal, add a lock washer, tighten the nut to a torque of 8-10N·m, and wrap with insulating tape or heat-shrink tubing for protection.

3. Connect excitation cable: Connect the excitation control cable to the F/L terminal, ensuring a firm and non-loose connection.

4. Connect ground cable: Connect the generator housing ground cable to a reliable grounding point on the engine block to avoid poor contact.

5. Organize wiring harness: Secure with cable ties and keep away from high-temperature components (e.g., exhaust pipe) and moving parts to prevent abrasion or short circuits.

4. Reconnect the Battery

IV. Post-installation Commissioning and Testing

1. Idle Speed Test

• Start the engine and run at idle for 5 minutes. Observe that the generator has no abnormal noise or odor, and the belt does not slip.

• Use a multimeter to measure the battery terminal voltage: 13.5-14.8V at idle (12V system standard), and not less than 12.8V when high-power loads such as headlights and air conditioners are turned on.

2. Load Test

• Turn on all electrical equipment in sequence and run for 10 minutes.

• Measure the output current with a current clamp in series. For a 75A generator, the current under full load should be 67.5-82.5A (±10% of the rated value), and the voltage should remain stable without significant fluctuations.

3. Visual and Insulation Inspection

• After stopping the engine, check that the wiring terminals are not overheated or loose, the belt tightness is normal, and there is no leakage from the housing.

• Retest the winding insulation resistance with an insulation resistance tester to ensure it is ≥1MΩ.

V. Installation Precautions

Electrical Safety

• Disconnect the negative battery cable throughout the installation process; do not plug or unplug wiring while the power is on. Avoid short-circuiting the B+ terminal to the vehicle body ground to prevent burning the stator winding.

• Ensure wiring terminals are crimped firmly, insulation protection is in place, and the wiring harness is routed away from high-temperature and moving parts.

Mechanical Installation

• Tighten the fixing bolts to the specified torque. Loose bolts will cause belt slipping and abnormal noise, while over-tightening will damage the bracket or generator housing.

• Strictly control belt tightness. Excessive tightness will accelerate bearing wear, and insufficient tightness will reduce power generation efficiency and heat dissipation effect.

References：

Source Explanation and Traceability of This Installation Method

I. Labeled Sources and Actual Corresponding Relations

II. Traceability of Key Content

1. Mechanical Installation and Torque

2. Electrical Connection and Safety

3. Testing Parameters

III. Reasons for Labeling as "Comprehensive Compilation"

• Wuling's original factory manuals are released by vehicle model, and specific model parameters need to be retrieved through official systems. Most public data are general guidelines without an independent chapter for "12V 75A".

• This article integrates vehicle model processes, engine torque, national standard safety requirements, and industry testing standards into complete, directly operable steps, balancing universality and practicality.

IV. Ways to Obtain Authoritative Data

1. Wuling Original Factory Manual

   Contact SAIC-GM-Wuling authorized service stations and provide the VIN/engine number to obtain the maintenance manual for the corresponding model, which includes the generator installation chapter.
2. National Standard

   Log in to the National Standard Full-Text Public System or CNKI and search for "GB/T 23642-2022" to obtain the original text.
3. Industry General Specifications

   Refer to general processes, torque values, and testing parameters for passenger vehicle generator installation, such as belt deflection and terminal torque.