
24V 6.0KW 11T Starter Motor QDJ251 for Chaochai 6102, 6105 engines and CY6102 series
Applicable models:Chaochai (Chaichai) 6102, 6105 engines and CY6102 series (BG/BZ/CG) (verify engine, equipment and OE number before ordering)
Reference part number:QDJ251 21020BA005
| Power horsepower : | 24v 6.0kw |
| Number of feet : | 11T |
| Size : | 44*24*20 single unit inner box |
| Weight : | net weight:8.65KG gross weight:9.2KG |
| Packaging : | Neutral kraft paper packaging |
| Spot/Pre sale : | Spot goods |
| Warranty : | 1 year |
| Product number : |
| Type : | ENGINE STARTER |
| Specification : | 24v 6.0KW |
| Number of feet : | 11T |
| Brand : | nuojin |
| Number : | QDJ251 21020BA005 |
| Quality : | new |
| Delivery time : | 10 day |





Overview of the QDJ251 Starter Motor
The QDJ251 starter motor is a 24V, 6.0 kW unit built for Chaochai 6102, 6105 engines and CY6102 series. It is a reduction-gear starter with a pre-engaged solenoid, assembled to the original mounting flange and terminal positions so it fits without adapters or wiring changes.
Because the motor is only used in short bursts, heat builds up quickly and escapes slowly. A starter that has worked for years in traffic or on site will show heat-hardened resin, shortened brushes and a pitted solenoid contact long before the windings fail.
Technical Summary
- Rated voltage: 24V
- Rated output: 6.0 kW
- Pinion: 11 teeth
- Type: reduction gear starter with pre-engaged solenoid
- Application: Chaochai 6102, 6105 engines and CY6102 series
- Net weight: approximately 9.2 kg
- Condition: new, direct replacement for the original unit
A 24V 6.0 kW rating is the output the motor can hold while cranking, not a peak figure. It is sized so the engine reaches starting speed on the first or second revolution, which is what makes a healthy start feel immediate.
The reduction gearset lets the motor run at high speed while the pinion turns slowly with high torque, which is why the unit stays compact enough for a crowded engine bay.
Reference Numbers and Cross References
Cross references for this starter are listed below. They are a matching aid rather than a substitute for checking the number on the old unit:
- QDJ251
- 11-tooth
- 21020BA005
- QDJ276B
Where the label on the old starter has corroded, compare the pinion teeth, the mounting flange and the terminal bracket with the photographs before ordering. The number on the original unit is the reliable identifier. This starter is listed with 4 references in total.
Application Notes
The unit is listed for Chaochai 6102, 6105 engines and CY6102 series. Because manufacturers changed starter suppliers during the production run, the safest check is the number stamped on the starter body, not the model year alone. The QDJ251 is built to the same flange pattern as the unit it replaces.
Vehicles that have had an engine or gearbox replacement may already carry a different starter from the one the catalogue expects, so treat the paperwork as a starting point rather than the final answer.
Failure Causes
Heat is the underlying cause in most cases. The starter sits close to the exhaust, and after a hot shutdown the solenoid winding and brush plate soak in heat with no airflow. Resin hardens, springs lose tension and the contact oxidises.
The brush plate is the second common failure point. Brushes shorten gradually, spring pressure falls, and contact becomes intermittent. Cranking speed drops a little every week until the engine refuses to start on a cold morning. The QDJ251 ships with its solenoid fitted, so no parts have to be transferred from the old unit.
Fault Symptoms
- Cranking that sounds normal but takes longer than it used to
- Several attempts needed before the motor engages
- Black carbon dust inside the drive end housing
- Voltage dip that dims the lights during cranking
- Starter that responds to a tap on the housing but not to the key alone
On a high-mileage vehicle, worn brushes and a burnt solenoid contact usually arrive together. If the motor bench tests well but cranking is still weak in the car, inspect the main cable and earth path before fitting another starter. Owners of Chaochai 6102, 6105 engines and CY6102 series should treat the QDJ251 reference list as a starting point, not the final answer.
Before You Fit the Replacement
- Battery capacity under load, not just open-circuit voltage
- Terminal clamps and the main cable lug for corrosion or heat marks
- Earth strap between engine and chassis
- Ring gear teeth, visible through the starter aperture
- Key switch and signal wire voltage at the solenoid terminal
Most comebacks after a starter replacement trace back to something that was not checked before the unit went on: a tired battery, a corroded earth or a chipped ring gear. Ten minutes with a multimeter and a torch prevents the second repair.
Installation Notes
Disconnect the battery negative terminal, remove the intake parts that restrict access, then disconnect the main cable and the solenoid signal connector. Support the starter before removing the mounting bolts.
Check the ring gear through the aperture before fitting. Install the new unit with the original bolts, reconnect the cables in the same order and tighten the main terminal without over-stressing the stud. Crank briefly and confirm the pinion releases as the engine fires. Where a QDJ251 has been replaced before, check that the fitted unit still matches the reference list.
Quality Control and Supply from Hejian Nuojin Auto Parts Co., Ltd.
Hejian Nuojin Auto Parts Co., Ltd. manufactures starter and alternator components for the aftermarket. Every unit is bench tested for no-load current draw, solenoid pull-in and release voltage, pinion throw and running noise before packing.
Common references are kept in stock for fast dispatch, volume orders are delivered in around 30 days and each starter carries a one-year warranty against manufacturing defects.
Frequently Asked Questions
Does this starter come with the solenoid?
Yes. The unit is supplied complete with its solenoid, as shown in the product photographs. Mounting bolts are not included.
How long should a replacement starter last?
Service life depends on starting frequency, battery condition and heat exposure. On a daily-driven vehicle with clean connections, ten years or more is realistic.
Can I test the starter on the bench?
Yes. Apply battery voltage to the main stud and the signal terminal and check that the pinion throws and the motor turns. A clamp meter reading against the rated current will show whether the unit is drawing too much.
Is a 12V and a 24V starter interchangeable?
No. The voltage rating must match the vehicle system; fitting the wrong unit will damage the starter and the wiring.

